![]() |
Z390 Taichi Bios 1.80 problems |
Post Reply ![]() |
Page 123 5> |
Author | ||
marjohn56 ![]() Newbie ![]() Joined: 05 Nov 2018 Location: London Status: Offline Points: 21 |
![]() ![]() ![]() ![]() ![]() Posted: 14 Dec 2018 at 8:12pm |
|
Anyone else having issues with the 1.80 version?
I have an nvme Samsung as my boot device and after installing the 1.80 bios everything slowed to a crawl, my old 386 would have been quicker to boot! Reverted back to v1.51 and normal service was restored. Would have gone back to 1.60 but cannot find that one on my drives. |
||
![]() |
||
RLGL ![]() Newbie ![]() ![]() Joined: 29 Jul 2018 Location: MN Status: Offline Points: 229 |
![]() ![]() ![]() ![]() ![]() |
|
After the installation of the 1.80 version did you clear the cmos and go through and reset everything?
|
||
Asrock Z370 Gaming K6,Intel i7 8700K, ThermalTake Contact Silent12
EVGA RTX2070 EVGA 750 W Super Nova, 16G GSkill Ripjaws, F4-3200C16D-16GVKB, Samsung 960 Evo 500G M.2,Samsung 970 Evo 1T M.2 |
||
![]() |
||
marjohn56 ![]() Newbie ![]() Joined: 05 Nov 2018 Location: London Status: Offline Points: 21 |
![]() ![]() ![]() ![]() ![]() |
|
Well I reset to default settings, rebooted and went through my normal setup again.
|
||
![]() |
||
marjohn56 ![]() Newbie ![]() Joined: 05 Nov 2018 Location: London Status: Offline Points: 21 |
![]() ![]() ![]() ![]() ![]() |
|
I've just repeated the procedure to make sure I had done nothing stupid, exactly the same result, W10 is very sluggish, mouse is slow etc, all in all just not responsive.
|
||
![]() |
||
RLGL ![]() Newbie ![]() ![]() Joined: 29 Jul 2018 Location: MN Status: Offline Points: 229 |
![]() ![]() ![]() ![]() ![]() |
|
do you have anything plugged into the sata ports. some are shared with the m.2 slots
|
||
Asrock Z370 Gaming K6,Intel i7 8700K, ThermalTake Contact Silent12
EVGA RTX2070 EVGA 750 W Super Nova, 16G GSkill Ripjaws, F4-3200C16D-16GVKB, Samsung 960 Evo 500G M.2,Samsung 970 Evo 1T M.2 |
||
![]() |
||
marjohn56 ![]() Newbie ![]() Joined: 05 Nov 2018 Location: London Status: Offline Points: 21 |
![]() ![]() ![]() ![]() ![]() |
|
I do have drives on the SATA ports, but they are not conflicting with the NVMEs.
I have two NVMEs a 512Gb ( boot ) and a 1Tb work drive, they are in slots 1 & 3, I also have four SATA drives, two are in the appropriate sata3_2 & 3_3 and the other two drives are on the ASMEDIA ports. To add to the usual gfx card I also have a Soundblaster card, and a USB3 expansion card as I never appear to have enough USB ports! That card also has a couple of SATA3 ports on it as well, I only use them for hanging drives on temporarily if I need to. I have just completed a clean W10 install, using 1.60 ( found a copy ) Bios, update the bios and it crawls, revert back to 1.60 and all is fine, think I'll be sticking with 1.60, it ain't perfect but it works. |
||
![]() |
||
teegale ![]() Newbie ![]() Joined: 17 Dec 2018 Status: Offline Points: 25 |
![]() ![]() ![]() ![]() ![]() |
|
Came here to post this exact same thing. I updated to 1.80 and immediately noticed my Samsung 970 PRO slowing to a crawl. Something is seriously wrong with this version. I even ran userbenchmark and it said it was performing well below expectations. I reverted back to 1.60 and everything is fine now. I would NOT recommend updating from 1.60.
|
||
![]() |
||
teegale ![]() Newbie ![]() Joined: 17 Dec 2018 Status: Offline Points: 25 |
![]() ![]() ![]() ![]() ![]() |
|
Seems I can't edit my previous post but I also wanted to mention that I'm not using any SATA drives and my m.2 is installed in the 3rd spot (under the heatsink).
|
||
![]() |
||
marjohn56 ![]() Newbie ![]() Joined: 05 Nov 2018 Location: London Status: Offline Points: 21 |
![]() ![]() ![]() ![]() ![]() |
|
Phew.. thanks. Glad it's not just me. ![]() Been with ASRock for years, my z77 extreme6 was superb, never any problem, ;ets hope they can resolve this. |
||
![]() |
||
teegale ![]() Newbie ![]() Joined: 17 Dec 2018 Status: Offline Points: 25 |
![]() ![]() ![]() ![]() ![]() |
|
I figured I wasn't alone. Which is why I came here. I'll give the next update a shot. Thank god for being able to downgrade. |
||
![]() |
Post Reply ![]() |
Page 123 5> |
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |