ASRock.com Homepage
Forum Home Forum Home > Technical Support > Intel Motherboards
  New Posts New Posts RSS Feed - Z170m PRO4S beep codes
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Z170m PRO4S beep codes

 Post Reply Post Reply Page  <12
Author
Message
Cicca View Drop Down
Newbie
Newbie


Joined: 26 May 2016
Location: Turin
Status: Offline
Points: 8
Post Options Post Options   Thanks (0) Thanks(0)   Quote Cicca Quote  Post ReplyReply Direct Link To This Post Posted: 27 May 2016 at 3:28am
Just tried....nothing changes....that was not the problem.....Ouch
Other ideas..?!
Back to Top
parsec View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 04 May 2015
Location: USA
Status: Offline
Points: 4996
Post Options Post Options   Thanks (0) Thanks(0)   Quote parsec Quote  Post ReplyReply Direct Link To This Post Posted: 27 May 2016 at 11:35am
Have you done a UEFI/BIOS clear yet? You can do that by moving the jumper on the CLR_CMOS header. That header is on the lower edge of the board, on the right side.

Do you know how to do that? Be sure the PC is off, PSU is off and disconnected from AC power.
Back to Top
Cicca View Drop Down
Newbie
Newbie


Joined: 26 May 2016
Location: Turin
Status: Offline
Points: 8
Post Options Post Options   Thanks (0) Thanks(0)   Quote Cicca Quote  Post ReplyReply Direct Link To This Post Posted: 27 May 2016 at 2:22pm
Yes, I did it twice....once before removing the video card (since I had moved the DIMMs from a slot to another), and then after.....same threee long beeps immediatly at the power up....
Back to Top
Xaltar View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 16 May 2015
Status: Offline
Points: 5825
Post Options Post Options   Thanks (0) Thanks(0)   Quote Xaltar Quote  Post ReplyReply Direct Link To This Post Posted: 27 May 2016 at 2:38pm
OK, now try removing the RAM from the system entirely and see if you get the same beep code without it. If the code is different then the RAM is not the problem.
Back to Top
Cicca View Drop Down
Newbie
Newbie


Joined: 26 May 2016
Location: Turin
Status: Offline
Points: 8
Post Options Post Options   Thanks (0) Thanks(0)   Quote Cicca Quote  Post ReplyReply Direct Link To This Post Posted: 30 May 2016 at 2:33pm
Hi....update status: removed both DIMMs (from slots A2/B2), cleared the CMOS, turned on.....same three beeps.... Confused....turned off, mounted the DIMMs back, but in slots A1/B1, cleared the CMOS again, turned on....and....NO BEEPS.... Big smile
Now....the new problem is that it doesn't seem to post/boot....I say "seem" because I have no proper cable to connect the monitor (the video card has a Dispay Port output, but the MB no, and the monitor has no HDMI input)....but I hear no "beep" between the POST and the boot (in any case, it can't boot anything since the HD is empty)....
Now....what's your suggestion...?! Buy a cable, and see how it goes on....or try to mount the video card back....?!
Back to Top
Xaltar View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 16 May 2015
Status: Offline
Points: 5825
Post Options Post Options   Thanks (0) Thanks(0)   Quote Xaltar Quote  Post ReplyReply Direct Link To This Post Posted: 30 May 2016 at 2:54pm
Try mount the video card and see how it goes. Good luck.
Back to Top
Cicca View Drop Down
Newbie
Newbie


Joined: 26 May 2016
Location: Turin
Status: Offline
Points: 8
Post Options Post Options   Thanks (0) Thanks(0)   Quote Cicca Quote  Post ReplyReply Direct Link To This Post Posted: 03 Jun 2016 at 3:29pm
YEAH !!! It goes !!! Thanks for all the help !!! Big smile
Back to Top
Xaltar View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 16 May 2015
Status: Offline
Points: 5825
Post Options Post Options   Thanks (1) Thanks(1)   Quote Xaltar Quote  Post ReplyReply Direct Link To This Post Posted: 03 Jun 2016 at 4:08pm
Glad to hear it, awesome job Big smile
Back to Top
 Post Reply Post Reply Page  <12
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.06
Copyright ©2001-2018 Web Wiz Ltd.

This page was generated in 0.063 seconds.