Z270 Extreme 4 - Full HD Not Working |
Post Reply | Page 12> |
Author | |||||
MicD
Newbie Joined: 29 Jan 2017 Status: Offline Points: 10 |
Post Options
Thanks(0)
Posted: 29 Jan 2017 at 6:49pm |
||||
Hi,
Have spent so much time trying to get this to work and I am still stuck on 1024x768 on 'auto' mode. As below my attempts: - Disabled CSM - Enabled/disabled Fast Boot (the function works on UEFI Win10) - Tried onboard Intel iGPU with HDMI - Tried HDMI with GTX 980Ti (by default I use DP) - CMOS jumper reset - Updated monitor to latest driver - Updated to latest BIOS revision 1.20 - Can't flash BETA 1.33A? On USB drive, "cannot locate image file" - Tried to downgrade to 1920x1080 on desktop even Hardware - Dell S2716DG G-SYNC monitor (native 2560x1440) - GALAX HOF GTX 980Ti - Updated to latest BIOS and UEFI capable - Kingston HyperX DDR4 Memory - Intel 6600K CPU I have searched online for solutions, but I'm exhausted. I know my PC works 100% but this issue is annoying me, as I used to own an MSI Z170 and that full HD BIOS/UEFI worked great on that so was thinking if it was my monitor (its a modern and expensive Dell). I genuinely feel like returning this board because of it, but I hope that someone here can assist as I do like the board. Edited by MicD - 29 Jan 2017 at 7:18pm |
|||||
wardog
Moderator Group Joined: 15 Jul 2015 Status: Offline Points: 6447 |
Post Options
Thanks(0)
|
||||
MicD
Newbie Joined: 29 Jan 2017 Status: Offline Points: 10 |
Post Options
Thanks(0)
|
||||
Yes.
|
|||||
MicD
Newbie Joined: 29 Jan 2017 Status: Offline Points: 10 |
Post Options
Thanks(0)
|
||||
wardog
Moderator Group Joined: 15 Jul 2015 Status: Offline Points: 6447 |
Post Options
Thanks(0)
|
||||
Oh settle down and take a breath. Think about it for a second. All the MB sees through the PCIe bus is the signal from the PCIe video card. This is between the 980to and the Dell monitor as those two are the ones communicating between themselves. Not the MB and monitor. I'll venture if you use the 6600's iGPU this doesn't happen. This would be MB to monitor, vs video card to monitor. Is either the 980ti or the S2716DG G-SYNC newly added? |
|||||
clubfoot
Newbie Joined: 28 Mar 2016 Location: Canada Status: Offline Points: 246 |
Post Options
Thanks(0)
|
||||
Do you have more than ONE video output/input connected to your monitor simultaneously?
Only use ONE for trouble shooting. If you have D-DVI or DP us that. D-DVI is better. Reset your monitor display settings to factory default (just for testing). In UEFI, F6, go to Advance menu and select Advance as your default UEFI menu,...AUTO for resolution. Did you make any changes to the UEFI for display output? iGPU or PCI? Shut down your PC. switch off the power supply, disconnect the power plug,....wait a minute or so or press the PC power button to discharge the power supply. Reconnect power cord, switch on PS and power up the PC. Does the UEFI still show in 1024x768 with one video input connected? |
|||||
MicD
Newbie Joined: 29 Jan 2017 Status: Offline Points: 10 |
Post Options
Thanks(0)
|
||||
I've tried the iGPU as mentioned, using HDMI as the ONE cable, Monitor>MB. Its still 1024x768 and Full HD as "auto" in advanced mode. I was hoping this would at LEAST work... Nope! Even with CSM disabled/enabled, there seems to be no difference.
The ASRock Z270 is the newest. All hardware was working 100% compatible when I had the MSI Z170 board displaying a Full HD UEFI. Edited by MicD - 30 Jan 2017 at 6:03am |
|||||
MicD
Newbie Joined: 29 Jan 2017 Status: Offline Points: 10 |
Post Options
Thanks(0)
|
||||
No, I only use one output and that is DP. But I have been testing between HDMI/DP. Unfortunately I cannot use D-DVI as the Dell S2716DG only has HDMI & DP. And I only have one monitor to test on hand.
I will try this a bit later, thanks.
This has always been on AUTO for obvious reasons. There really should be an ON to force Full HD...
I was testing as below (under Chipset config menu)
Tested using HDMI and DP. Only difference is HDMI cannot handle 144hz (desktop) unlike DP. Both still low res when UEFI when booting.
Anything else that I need to change?
Yes unfortunately since I have installed it, it has never been displayed in Full HD. I also have only used one cable (DP) due to the 144hz capability. I am just frustrated as mentioned, it worked on an MSI Z170 using the same hardware, same cables but this ASRock board just isn't playing ball.
Edited by MicD - 30 Jan 2017 at 6:21am |
|||||
Raptorta
Newbie Joined: 19 Jan 2017 Status: Offline Points: 4 |
Post Options
Thanks(0)
|
||||
Enable CSM and Force "Video OProm policy" to legacy only.
|
|||||
MicD
Newbie Joined: 29 Jan 2017 Status: Offline Points: 10 |
Post Options
Thanks(0)
|
||||
I could try this for testing purposes only. What about the other two options - PXE and Storage OpROM, shoud they be Legacy/UEFI only/Do not launch? I can confirm that Fast Boot works when CSM disabled of course, but happy to test above.
|
|||||
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |