x570 Taichi - all the issues I've had thus far |
Post Reply | Page 123> |
Author | |
shmerl
Groupie Joined: 23 Oct 2017 Status: Offline Points: 612 |
Post Options
Thanks(0)
Posted: 24 Jul 2019 at 4:48am |
That is horrible. Sounds like the fan is defective. I wonder if anyone will figure out custom cooling solutions for such chipsets? They can really benefit from bigger and more silent fans. |
|
TheBigNoob
Newbie Joined: 23 Jul 2019 Status: Offline Points: 1 |
Post Options
Thanks(0)
|
I've had a mostly okay experience with the X570 Taichi, until yesterday morning when I got back into the office. Sounds like my chipset fan is grinding already, anyone have any ideas? I've attempted to contact ASRock, but still no response yet.
Here's a video of the fan starting up. https://photos.app.goo.gl/9oHaDFcNBZRseVqo8 Hopefully they can send me out a replacement cooler. Also, does anyone seem to have a pair of calipers to determine the distance between the board and the and the rear backplate? I'm trying to figure out if there's a way I can put a heatpad there to help conduct heat away from the chipset and onto the metal that's behind the board. |
|
mrgadget
Newbie Joined: 22 Jul 2019 Status: Offline Points: 14 |
Post Options
Thanks(0)
|
Quiet profile works but I have configured it manually. I'd say 3500 rpm or lower it is quite silent, or my other fans make more noise. I don't have an issue with the fan but I could imagine if someone has started building and #1 priority has been noise levels then you might be in trouble. I have front fans (140mm), top fan (200mm) and side fan (140mm). That 3500 rpm equals about 45% power and chipset temp is around ~59-63C. |
|
foxx1337
Newbie Joined: 19 Jul 2019 Location: Munich Status: Offline Points: 89 |
Post Options
Thanks(0)
|
Hey Cecil - what are the power and current readouts on your 3900X + Taichi X590? Mine are very wrong, half of what they should be. If I turn off a CCD they get halved once again so I'm in a bit of a pickle here whether to do anything about anything.
PPT - 70 watts TDC - 43 amps as seen in Ryzen Master during a Prime95 small FFT test https://imgur.com/a/Z01Nu4H or in HWiNFO64 at the same time https://imgur.com/a/nDkakhs What values do you see? |
|
Ryzen 3900X, Taichi X570
|
|
Disturbed
Newbie Joined: 22 Jul 2019 Status: Offline Points: 18 |
Post Options
Thanks(0)
|
I set fan to manual as a part oboe started (25/30% @ 60c) and that helps a ton.
|
|
shmerl
Groupie Joined: 23 Oct 2017 Status: Offline Points: 612 |
Post Options
Thanks(0)
|
So what's the current situation with chipset fan noise with X570 Taichi? Is quite profile helping with it?
|
|
shmerl
Groupie Joined: 23 Oct 2017 Status: Offline Points: 612 |
Post Options
Thanks(0)
|
Good to know thanks! |
|
mrgadget
Newbie Joined: 22 Jul 2019 Status: Offline Points: 14 |
Post Options
Thanks(0)
|
|
|
Xaltar
Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 24713 |
Post Options
Thanks(0)
|
PCIe 3.0 x8 is still more than enough for modern GPUs, you shouldn't have any issues running at x8, I have not seen any performance drops using any of the GPUs I have tested in x8 slots. Dropping to an x4 slot may cost you 5-10fps on a high end GPU in some games but even there, generally your performance will remain unchanged. Moreover, if you game at higher resolutions than 1080p the GPU will become a bottleneck LONG before you eat up your PCIe bandwidth, even on an x4 slot. This becomes an even more moot point if you are able to utilize PCIe 4.0 which effectively doubles PCIe 3.0 bandwidth. At present I believe only AMD's new 5700 series GPUs support PCIe 4.0 however.
This is a little understood area for a lot of people, I hope this helps to clarify. |
|
|
|
Disturbed
Newbie Joined: 22 Jul 2019 Status: Offline Points: 18 |
Post Options
Thanks(0)
|
So only the top is x16 but the manual says all 3 are? Wtf is that about. My card won't fit in top either because of the same reason.
|
|
Post Reply | Page 123> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |