Z690 Steel Legend-Corsair 3600mhz |
Post Reply | Page 12> |
Author | |
fille1976
Groupie Joined: 31 Dec 2021 Status: Offline Points: 290 |
Post Options
Thanks(0)
Posted: 31 Dec 2021 at 5:13am |
Hi,
I have a z690 Steel legend motherboard with i9 12900kf and rtx 3090. I wanted to fit corsair vengenace rgb pro 3600 mhz. Works,only 3000mhz,tryed manual and with xmp,not working. System failed to boot message,with xmp and set to 3000 mhz it boots. It are 4x8gb sticks,its CMW32GX4M4D3600C18. 2x8gb is supported,but seems 4x8gb is not,can this be fixed please? |
|
fille1976
Groupie Joined: 31 Dec 2021 Status: Offline Points: 290 |
Post Options
Thanks(0)
|
I got in the meantime to 3100 mhz,but if i go higher i get system failed to boot.
So what can be the problem here? I checked the sticks,they match the numbers on the box. I readed in the manual the motherboard goes to 5000(oc) Is this a compatibility problem that can be solved with a bios update? |
|
ASRock_TSD
ASRock_Official Joined: 20 Mar 2015 Status: Offline Points: 8727 |
Post Options
Thanks(0)
|
Hi fille1976,
Could you help to check which version is your memory module? This will help us to simulate your system. You can help it on the label of the memory module. CMW32GX4M4D3600C18 ver.X.XX At the same time, you can also try to verify your system with the below suggestions. 1. Enter BIOS setup and load BIOS default settings via [F9] key and press [F10] to save the settings and exit. 2. Load XMP profile (OC Tweaker\DRAM Configuration\Load XMP Setting). Press "F10" to apply the setting 3. Install one stick RAM on each slot by turns to repeat suggestion 2 to check if the problem relates to a specific RAM stick or slot. All the best ASRock TSD |
|
fille1976
Groupie Joined: 31 Dec 2021 Status: Offline Points: 290 |
Post Options
Thanks(0)
|
fille1976
Groupie Joined: 31 Dec 2021 Status: Offline Points: 290 |
Post Options
Thanks(0)
|
Any info if this will be fixed please?
|
|
ASRock_TSD
ASRock_Official Joined: 20 Mar 2015 Status: Offline Points: 8727 |
Post Options
Thanks(0)
|
Hi fille1976, Thank you for your information. But we need the detailed model on the memory module to check the problem. Please help take a photo of the memory itself, usually, you can find the barcode on the memory heat sink. The version number will nearby the barcode. The version number can let us get the same model to verify the problem. All the best ASRock TSD |
|
fille1976
Groupie Joined: 31 Dec 2021 Status: Offline Points: 290 |
Post Options
Thanks(0)
|
fille1976
Groupie Joined: 31 Dec 2021 Status: Offline Points: 290 |
Post Options
Thanks(0)
|
Any progress?
|
|
kerberos_20
Senior Member Joined: 06 Dec 2017 Location: czech republic Status: Offline Points: 3657 |
Post Options
Thanks(0)
|
thats samsung C-die...or really bad B-die bin your memory sticks arent listed in mainboard memory QVL compatibility list and C-die tops out there at 3200MHz with 4 sticks you have few options, return ram and pick some which were tested memory compatibility list can be found here https://www.asrock.com/mb/Intel/Z690%20Steel%20Legend/index.asp#Memory dont use XMP if it doesnt work, XMP is overclock for beginners...and as with any overclock, its not guaranteed to work, you can use XMP and set up your stable frequency, then tighten timings as much you can. that will be your baseline. once you know working frequency with its timings, then you just increase frequency alongside with loosening timings based on your baseline. there are plenty of ram overclocking guides, but basicly its just mathematics another option would be replacing CPU, as memory controller resides there, its not uncommon to have bad bin on memory controller Edited by kerberos_20 - 18 Feb 2022 at 6:22am |
|
fille1976
Groupie Joined: 31 Dec 2021 Status: Offline Points: 290 |
Post Options
Thanks(0)
|
The store doesn't take them back,so its gona be the same with the cpu,ill refuse to ever buy something from alternate again,its the worse store i knew,same as newegg.
Can't asrock fix this in a bios update?? So how the hell corsair can sell those if those are bad sticks. Also the cpu,its brand new,if feel i am scammed here. |
|
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |