Mobo+CPU upgrade No Post+Blackscreen

parsec wrote: Phil86 wrote: [URL=][/URL]Hello everyone, Today i upgraded my Rig from MSI970A-G46+FX6350 to a ASRock Fatal1ty Z170+i56600k. Other Speccs; 750W PSU 2xKingston Hyperbeast 1600Mhz DDR3 8Gb CPU Cooler: Coolermaster V8 Vapor Samsung Evo 250Gb SSD Seagate Barracuda 1Tb HDD Raedon R9 280x 3Gb Windows 10 After i was done with the reassembly of the components i turned the System on and it went off after half a second then it reboots and all LEDs, FANs and visible Components are running. There is no Post, My Monitor is not recieving a Video Signal and enters Sleep Mode. But the Components keep running until i do a Hard reboot/shutdown. Gotta say the CPU Cooler sounds a little different from.the previous Setup. I have so far, reassembled everything to see if all the Pins and Connectors are correctly in place and have a tight fit. Reapplied thermal paste (using Coolermaster IC 1V). Reset the CMOS Battery. Started booting in secondary BIOS (May be important to mention that in both cases the LED was a solid constant red). Tried plugging in VGA Monitor instead of HDMI. Tried onboard Video plugins. I dont have a second CPU Cooler at hand atm so i dont know, the V8 is HUGE and a Beast. The split second reboot at start makes me wonder if its a Power Supply issue,but then again it wouldnt run stable afterwards would it? And one additional question; Does it matter wether i plug the CPU Fan into CPU_FAN1 or2?? I have one Pin Connector for USB_Card Reader plugged into one of the two USB2.0 recievers on the Mobo, thats basically the only thing im not sure with. And by now i tripple checked ALL the Pins for PWR, REset etc are correctly in place. Please id be glad for ANY suggestions here because i cant think of anything else that might be the cause. Dear God let it not be broken :D. Greetings, Phil Edit: Forgot to mention that eventhough the pins are all in their correct place, the Reset Button does not work. So let me be sure this is right. You simply moved your Windows 10 installation/drive? from an AMD chipset board and processor system, to an Intel chipset board and processor system. That is what it sounds like from your description. The chances of your Windows 10 installation on an AMD system booting on an Intel system is very small, or none. What was the SATA mode set to on the AMD board? While all you told us was ASRock Fatal1ty Z170 as the board you have, and there are six different ASRock Z170 boards with "ASRock Fatal1ty Z170" as part of the name model name, so we have no idea what board you have. http://www.asrock.com/mb/index.asp The CPU cooler sounding different is simply the difference in the fan speed control setting between the two boards in their BIOS. The fan(s) were running faster or slower, that's all. The CPU fan header in use will not stop the PC from completing POST or boot. The BIOS LEDs just indicate which one is in use, and should be on, and are red. How do you know that POST did not complete? Remove that card reader for now. We need the full model number of your Kingston memory to check for compatibility with your Intel CPU. The Reset button should work, is the polarity correct?

Hey,

yeah that is what i did, i figured it would be possible for the System to boot from Disc eventhough the Hardware had significantly changed, its my first Intel system ever so i didnt know that there could be such unforgiving circumstances.

The exact description would be;

ASRock Fatal1ty Z170 Gaming K4/D3

The SATA Mode was set to IDE.

As far as I know the POST completion is marked with a beep, and i have no Sounds whatsoever.

Yes, the Reset polarity was correct.

Im not sure where to find the Modell number of those RAMS so ill give you the two most likely Numbers from the retail Box:

16GBb DDR-1600 CL9 240-Pin UDIMM Kit

KHX16C9T3K2/16X.

Thanks for the help, if i dont answer in Time its probably due to the fact that its right now 7am here and ill hit the hay.

Greets




Edited by Phil86 - 23 Oct 2016 at 8:17pm

Hello everyone,

Today i upgraded my Rig from MSI970A-G46+FX6350 to a ASRock Fatal1ty Z170+i56600k.
Other Speccs;

750W PSU
2xKingston Hyperbeast 1600Mhz DDR3 8Gb
CPU Cooler: Coolermaster V8 Vapor
Samsung Evo 250Gb SSD
Seagate Barracuda 1Tb HDD
Raedon R9 280x 3Gb
Windows 10

After i was done with the reassembly of the components i turned the System on and it went off after half a second then it reboots and all LEDs, FANs and visible Components are running.
There is no Post, My Monitor is not recieving a Video Signal and enters Sleep Mode.
But the Components keep running until i do a Hard reboot/shutdown.
Gotta say the CPU Cooler sounds a little different from.the previous Setup.

I have so far, reassembled everything to see if all the Pins and Connectors are correctly in place and have a tight fit.
Reapplied thermal paste (using Coolermaster IC 1V).
Reset the CMOS Battery.
Started booting in secondary BIOS (May be important to mention that in both cases the LED was a solid constant red).
Tried plugging in VGA Monitor instead of HDMI.
Tried onboard Video plugins.

I dont have a second CPU Cooler at hand atm so i dont know, the V8 is HUGE and a Beast. The split second reboot at start makes me wonder if its a Power Supply issue,but then again it wouldnt run stable afterwards would it?
And one additional question; Does it matter wether i plug the CPU Fan into CPU_FAN1 or2??
I have one Pin Connector for USB_Card Reader plugged into one of the two USB2.0 recievers on the Mobo, thats basically the only thing im not sure with.
And by now i tripple checked ALL the Pins for PWR, REset etc are correctly in place.

Please id be glad for ANY suggestions here because i cant think of anything else that might be the cause.

Dear God let it not be broken :D.

Greetings,

Phil

Edit: Forgot to mention that eventhough the pins are all in their correct place, the Reset Button does not work.

Edited by Phil86 - 23 Oct 2016 at 10:10am