takes tries to boot up

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   I have to press the power button 3 times to get the motherboard to boot.  It works after it boots up.
each time the fan spins for a tiny bit and shutdown third press and it works

H97M PRO4

what I've done
got bios 2.20
removed battery for a minute
tried the cmos clear jumper
brand new power supply (even the old one was working...)
swapped power and rest buttons (same thine still takes 3 tries)

So I think its broken unless someone has a hint?

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
joeb1355 Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 02 Dec 2016 Status: Offline Points: 3	Post Options Post Reply Quote joeb1355 Report Post Thanks(0) Quote Reply Topic: takes tries to boot up Posted: 02 Dec 2016 at 5:51am
	I have to press the power button 3 times to get the motherboard to boot. It works after it boots up. each time the fan spins for a tiny bit and shutdown third press and it works H97M PRO4 what I've done got bios 2.20 removed battery for a minute tried the cmos clear jumper brand new power supply (even the old one was working...) swapped power and rest buttons (same thine still takes 3 tries) So I think its broken unless someone has a hint?

jbkeh Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 25 Mar 2016 Status: Offline Points: 3	Post Options Post Reply Quote jbkeh Report Post Thanks(0) Quote Reply Posted: 04 Dec 2016 at 6:12am
	This might be a power problem (lack thereof). If the PSU is barely adequate to support the system when it is running, the boot process may be pulling more power than the PSU can deliver from a cold start and only after a few tries has enough residual power in its capacitors. Is the new PSU a significant increase in power capability that matches whatever increases in power requirements the new build entails?

jbkeh Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 25 Mar 2016 Status: Offline Points: 3	Post Options Post Reply Quote jbkeh Report Post Thanks(0) Quote Reply Posted: 04 Dec 2016 at 6:52am
	And to follow up... You said the old PSU was "working". Was that with this new system (in which case you have already identified the source of your problem)? If not, have you tried the "old" PSU with the new build?

ASRock_TSD Members Profile Send Private Message Find Members Posts Add to Buddy List ASRock_Official Joined: 20 Mar 2015 Status: Offline Points: 8532	Post Options Post Reply Quote ASRock_TSD Report Post Thanks(0) Quote Reply Posted: 13 Dec 2016 at 6:21pm
	Dear joeb1355, Greetings, this is ASRock TSD. Because our latest BIOS version on official website is P2.10, so please refer below link to upgrade latest BIOS P2.10 for trying again. http://www.asrock.com/mb/Intel/H97M%20Pro4/?cat=Download&os=BIOS Here's the SOP of Instant Flash: http://www.asrock.com/support/BIOSUI.asp?cat=BIOS8 According to your question, we also provide some suggestions to verify: 1. Please enter the BIOS setup then press[F9] to load BIOS default setting to try. 2. Please clean the Goldfinger parts of memory and re-connect to the motherboard, make sure it has been installed correctly. 3. Remove the CPU and check if the CPU socket pin-bent. 4. Only install the necessary devices (CPU and one stick memory ) to check if the system can boot properly. 5. Only install one stick memory module to each DRAM slot by turns to try. 6. If possible, please install another memory module / CPU / PSU to verify. Thanks! All the best, ASRock TSD