![]() |
Z270 Extreme4 Software or hardware issue? |
Post Reply ![]() |
Page 12> |
Author | ||
PaulGC ![]() Newbie ![]() Joined: 24 Mar 2017 Location: AUS Status: Offline Points: 8 |
![]() ![]() ![]() ![]() ![]() Posted: 10 Apr 2017 at 3:05pm |
|
Ok, ill let you know how it goes. Thanks
|
||
![]() |
||
Xaltar ![]() Moderator Group ![]() ![]() Joined: 16 May 2015 Location: Europe Status: Offline Points: 25508 |
![]() ![]() ![]() ![]() ![]() |
|
The best method is using a razor blade to line up each row/column/diagonal. Just be very careful not to bend any more pins in the process. You will probably want to use a magnifying glass and really take your time.
|
||
![]() |
||
![]() |
||
PaulGC ![]() Newbie ![]() Joined: 24 Mar 2017 Location: AUS Status: Offline Points: 8 |
![]() ![]() ![]() ![]() ![]() |
|
Ok RMA Failed , Even the retailer though they would throw in a new socket.
Ill have a go at straightening the bent pins
|
||
![]() |
||
Xaltar ![]() Moderator Group ![]() ![]() Joined: 16 May 2015 Location: Europe Status: Offline Points: 25508 |
![]() ![]() ![]() ![]() ![]() |
|
If are still within your RMA window I would go ahead and do that.
ASRock are pretty good with the bent pin issue, probably because it is an easy enough fix for them. If the RMA doesn't go through for some reason then post back and I can talk you through trying to straighten the offending pins.
|
||
![]() |
||
![]() |
||
PaulGC ![]() Newbie ![]() Joined: 24 Mar 2017 Location: AUS Status: Offline Points: 8 |
![]() ![]() ![]() ![]() ![]() |
|
Dropped the pc into a local It service guy today to see if he had any suggestions also asked him to reseat cpu in case i had screwed it up.
picked it it up, he just said it seems like a motherboard issue... no sh*t .! just stripped it down again and there is bloody thermal paste everywhere from the it guy, not happy. Pulled the cpu and got a torch to check pins and looks like iohave a few bent pins on the MB. dont know how that would have happened as i was so careful seating the cpu. I can only assume this is my error as they wouldnt come like this from the supplier? is this fixable or am i up for a new MB
![]() |
||
![]() |
||
PaulGC ![]() Newbie ![]() Joined: 24 Mar 2017 Location: AUS Status: Offline Points: 8 |
![]() ![]() ![]() ![]() ![]() |
|
|
||
![]() |
||
wardog ![]() Moderator Group ![]() Joined: 15 Jul 2015 Status: Offline Points: 6447 |
![]() ![]() ![]() ![]() ![]() |
|
I better ask this too now that I re-read your posts for the third time. ![]() In the BIOS, what are your temps looking like? |
||
![]() |
||
wardog ![]() Moderator Group ![]() Joined: 15 Jul 2015 Status: Offline Points: 6447 |
![]() ![]() ![]() ![]() ![]() |
|
Hmmmm ...... Have you tried using the Windows to USB tool from Microsoft? It works with a local ISO and as a new download. https://www.microsoft.com/en-us/download/windows-usb-dvd-download-tool I ask that as it could be whatever program you're currently using has a "switch' that isn't properly set. But, more than likely it sounds like your memory is not fully seated. You should hear two clicks when it's in. I'm assuming in both above you have no issue entering and navigating around in the BIOS. |
||
![]() |
||
PaulGC ![]() Newbie ![]() Joined: 24 Mar 2017 Location: AUS Status: Offline Points: 8 |
![]() ![]() ![]() ![]() ![]() |
|
Installing Windows 10 Pro
|
||
![]() |
||
parsec ![]() Moderator Group ![]() ![]() Joined: 04 May 2015 Location: USA Status: Offline Points: 4996 |
![]() ![]() ![]() ![]() ![]() |
|
ASRock mother boards will not send a POST beep speaker signal until the option to do that is set to Enabled in the UEFI/BIOS, Boot screen. POST beep is disabled by default, and you must install your own POST beep speaker.
|
||
![]() |
Post Reply ![]() |
Page 12> |
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |