AMD Ryzen Compatible Memory List

hello @solarwnz

Your problem is somewhere else and you can make them work with manual settings.

switching to other rams listed in QVL will not necessary work because you run too many ram...... i.e. first you have to know about this rule, apply to both Intel and AMD, see this link http://forum.asrock.com/forum_posts.asp?TID=15975&KW=&PID=79200&title=memory-clock-on-asrock-x570-creator#79200

and get tips from this link http://forum.asrock.com/forum_posts.asp?TID=15975&KW=&PID=79223&title=memory-clock-on-asrock-x570-creator#79223

this helps too http://forum.asrock.com/forum_posts.asp?TID=15699&KW=&PID=79187&title=ab350-gamingitx-ac-tridentz-16gb-only-2133-mhz#79187

finally this http://forum.asrock.com/forum_posts.asp?TID=15975&KW=&PID=79186&title=memory-clock-on-asrock-x570-creator#79186

Good luck.

Your board can handle 4 sticks of ram either single or dual rank but running 4 sticks they only guarantee stability at slower speeds. The CPU runs the ram stock 3200 mhz with 1 stick or 2 sticks paired in the right slots either Single ranked or Dual Ranked. when you go to 4 sticks of either single or dual ranked it slows the stock speed it guarantees down to 2933 for 4 SR chips or 2667 mhz for 4 DR chips. You might be able to run them faster all the way up to 4333 but it would require a nice PSU and some luck maybe a touch of voltage.



UDIMM Memory Slot            Frequency
A1    A2    B1     B2        (Mhz)
-     SR    -      -        3200
-     DR    -      -        3200
-     SR    -      SR        3200
-     DR    -      DR        3200
SR    SR    SR     SR        2933
SR/DR DR    SR/DR DR        2667
SR/DR SR/DR SR/DR SR/DR     2667

Hello! I'm running into some trouble with my build. I'm trying to upgrade from AMD Ryzen 2700x to 5800x

Motherboard: X570 Pro4 Asrock

CPU: AMD Ryzen 5800x



Upgrading from AMD Ryzen 2700x



Issue: When I turn it on, everything turns on, fans spin, Red Light on VGA and DRAM. All my parts work on my Ryzen 2700x.



We have updated the bios to the latest version

We reset the CMOS

We have tried different ram slots and singular ram (even though its working on those slots with the 2700)



Anyone have an idea as to what I should do? I'm a bit lost and documentation is kind of bad

We have tried everything in this post: http://forum.asrock.com/forum_posts.asp?TID=17204

I'd appreciate some guidance here?

This is my solution for using 3600 GSKILL GTZRC memory. I believe the memory is Hynix CJR or DJR RAM and DRAM Calculator for Ryzed showed the tRP timing, SOC, VDDGG and VDDP voltages were all improperly set by the BIOS and XPM.

I have 2 different systems and they both had issues getting RAM work at any speed over SPD 2133. I spent some time figuring it out and wanted to share this post so others my benefit.

Problems witnessed:
Reboots would hang the system with BIOS code 8d.
System would not ran stable with memory clocked over 3200.
Would have to reset the BIOS some times just to get booted again.

After making Memory timing and voltage changes below, both systems have been running flawlessly at 3600 with Fabric Clock at 1800. Clean reboots and stability have been achieved!

Motherboard: Asrock AQUA X570
BIOS: 3.30
CPUs: 3950x 100-100000051WOF and 3900X 100-100000023BOX
Video Card: ASUS ROG Strix RTX 2070 ROG-STRIX-RTX2070-O8G-GAMING
Storage: SSD Samsung 970 EVO PLUS M.2
Memory: 64GB of G.Skill Trident Z RGB F4-3600C16Q-64GTZRC
Operating System: Windows 10 20H2

load the XPM profile and changing the following settings:
Memory timing tRP from 19 to 21
DRAM Voltage (should already be set by XPM) 1.35
SOC Voltage 1.03
VDDG (CCD and IOD) 1.00
cLDO VDDP Voltage 0.90
DRAM Frequency 3600
Infinity Fabric Frequency 1800

Optionally:
I locked my PCIe to GEN3... not sure if this did anything to help.

There may be other adjustments that would improve speed, but I am happy with this... good stability and performance is well above average for the configuration.


Hope this helps out others!

I have a B350 Pro4 and I use EVGA 3000 memory.