ASRock.com Homepage
Forum Home Forum Home > Technical Support > AMD Motherboards
  New Posts New Posts RSS Feed - AGESA 1.0.0.6a
  FAQ FAQ  Forum Search Search  Events   Register Register  Login Login

AGESA 1.0.0.6a

 Post Reply Post Reply Page  <1 1213141516 23>
Author
Message
CJG View Drop Down
Newbie
Newbie
Avatar

Joined: 12 Jun 2017
Status: Offline
Points: 8
Post Options Post Options   Thanks (0) Thanks(0)   Quote CJG Quote  Post ReplyReply Direct Link To This Post Posted: 19 Jul 2017 at 12:31am
AGESA 1.0.0.6a
This took some tweaking but it works the best for me so far!
ASRock X370 Taichi : AGESA 1.0.0.6a
CPU CORE 1.376 V
VPPM 2.544 V
AVCC 3.344 V
3VCC 3.344 V
+12V 12.038 V
VDDCR_SOC 1.104 V
DRAM 1.360 V
VIN7 0.752 V
VDDP 0.992 V
+1.8V 1.824 V
VIN11 1.272 V
+5V 5.016 V
Chipset +1.05V 1.104 V
 
AMD Ryzen 7 1800X : Multiplier x40.0 = 4000.5 MHz 100% stable
RAM : G.SKILL TridentZ RGB Series 32GB (4 x 8GB) 288-Pin DDR4 SDRAM DDR4 3866 (PC4 30900) Desktop Memory Model F4-3866C18Q-32GTZR    
Where I'm at with it =         
32.0GB Dual-Channel @ 1733.5 MHz - Ratio 3:52 (3467 MHz)
Total memory slots 4
Used memory slots 4
Total Physical 32 GB
CAS# Latency               (CL) 18 clocks
RAS# to CAS# Delay (tRCD) 18 clocks
RAS# Precharge          (tRP) 18 clocks
Cycle Time                (tRAS) 38 clocks
Bank Cycle Time         (tRC) 56 clocks remember TRC SHOULD BE TRES + TRP TO be in sync!
Command Rate            (CR) 1T
 
For ram had to set in bios PROC to 48 and voltage to 1.38
Also I have found if you change anything in bios the CPU Multiplier needs to be raised and lowered and then set back to your setting or else it will not hold
Say for me it is running at 40 so every time I mess with memory I have to raise and lower then put back to 40 then save or else the Multiplier will show 40 in bios but will not run at 40
It will run at factory setting and just visually show 40 (4000mhz) in bios!
 
 


Edited by CJG - 21 Jul 2017 at 8:25am
Back to Top
datonyb View Drop Down
Senior Member
Senior Member


Joined: 11 Apr 2017
Location: London U.K.
Status: Offline
Points: 3139
Post Options Post Options   Thanks (0) Thanks(0)   Quote datonyb Quote  Post ReplyReply Direct Link To This Post Posted: 19 Jul 2017 at 2:19am
helpful info mate well done for sharing

[url=https://valid.x86.fr/jpg250][/url]

3800X, powercolor reddevil vega64, gskill tridentz3866, taichix370, evga750watt gold
Back to Top
metapsyborg22 View Drop Down
Newbie
Newbie
Avatar

Joined: 18 Jul 2017
Status: Offline
Points: 5
Post Options Post Options   Thanks (0) Thanks(0)   Quote metapsyborg22 Quote  Post ReplyReply Direct Link To This Post Posted: 19 Jul 2017 at 5:19am
Anyone getting good results updating the ab350 Fatal1ty K4? Trying to get my RAM a little tighter. 

Memory: F4-3000C15D-16VKB

Update: I updated the BIOS and overclock settings will not save for the CPU. Also, with ultra-fast boot enabled it wont boot. Any ideas?


Edited by metapsyborg22 - 19 Jul 2017 at 6:46am
Back to Top
Jakob View Drop Down
Newbie
Newbie


Joined: 25 Jun 2017
Status: Offline
Points: 26
Post Options Post Options   Thanks (0) Thanks(0)   Quote Jakob Quote  Post ReplyReply Direct Link To This Post Posted: 19 Jul 2017 at 5:25am
X370 K4 here. No real change. I don't seem to experience any trouble with case fans.
Resolution in POST screen (when BIOS options are shown) seems to be stable at native resolution of screen. Before, it was a lower resolution sometimes.
Will see, whether I see the low resolution again... Just updated a few hours ago
Back to Top
metapsyborg22 View Drop Down
Newbie
Newbie
Avatar

Joined: 18 Jul 2017
Status: Offline
Points: 5
Post Options Post Options   Thanks (0) Thanks(0)   Quote metapsyborg22 Quote  Post ReplyReply Direct Link To This Post Posted: 19 Jul 2017 at 11:51am
Not sure if this is related but I did the BIOS update, windows 10 started running and booting extremely slow. Reverted back to old bios and old working settings, still sluggish windows 10. Went through a bunch of other numerous "fixes" and landed on re-installing windows to fix. 

Again, not sure if its related to the bios update? Just wanted to post in case someone has a similar experience.

ab350 Fatal1ty K4


Edited by metapsyborg22 - 19 Jul 2017 at 11:51am
Back to Top
wardog View Drop Down
Moderator Group
Moderator Group


Joined: 15 Jul 2015
Status: Offline
Points: 6447
Post Options Post Options   Thanks (0) Thanks(0)   Quote wardog Quote  Post ReplyReply Direct Link To This Post Posted: 19 Jul 2017 at 11:58am
Originally posted by metapsyborg22 metapsyborg22 wrote:

Not sure if this is related but I did the BIOS update, windows 10 started running and booting extremely slow. Reverted back to old bios and old working settings, still sluggish windows 10. Went through a bunch of other numerous "fixes" and landed on re-installing windows to fix. 

Again, not sure if its related to the bios update? Just wanted to post in case someone has a similar experience.

ab350 Fatal1ty K4


The BIOS itself wouldn't be responsible. Is your 10 fully updated?

And that's not me shucking the buck over onto MS either.

Too, there are variables like the mem used, that may have affected it "some' but not "extremely"
Back to Top
wardog View Drop Down
Moderator Group
Moderator Group


Joined: 15 Jul 2015
Status: Offline
Points: 6447
Post Options Post Options   Thanks (0) Thanks(0)   Quote wardog Quote  Post ReplyReply Direct Link To This Post Posted: 19 Jul 2017 at 12:00pm
Nice CJG!

Ryzen is a lift the hood and tinker prissy.
Back to Top
metapsyborg22 View Drop Down
Newbie
Newbie
Avatar

Joined: 18 Jul 2017
Status: Offline
Points: 5
Post Options Post Options   Thanks (0) Thanks(0)   Quote metapsyborg22 Quote  Post ReplyReply Direct Link To This Post Posted: 19 Jul 2017 at 12:09pm
Originally posted by wardog wardog wrote:

Originally posted by metapsyborg22 metapsyborg22 wrote:

Not sure if this is related but I did the BIOS update, windows 10 started running and booting extremely slow. Reverted back to old bios and old working settings, still sluggish windows 10. Went through a bunch of other numerous "fixes" and landed on re-installing windows to fix. 

Again, not sure if its related to the bios update? Just wanted to post in case someone has a similar experience.

ab350 Fatal1ty K4


The BIOS itself wouldn't be responsible. Is your 10 fully updated?

And that's not me shucking the buck over onto MS either.

Too, there are variables like the mem used, that may have affected it "some' but not "extremely"

Checked memory usage and CPU, both were almost nothing. Uninstalled classic shell, still nothing. Windows ran like it was using up all the ram but it wasnt even touching 10%

Back to Top
wardog View Drop Down
Moderator Group
Moderator Group


Joined: 15 Jul 2015
Status: Offline
Points: 6447
Post Options Post Options   Thanks (0) Thanks(0)   Quote wardog Quote  Post ReplyReply Direct Link To This Post Posted: 19 Jul 2017 at 12:13pm
Originally posted by metapsyborg22 metapsyborg22 wrote:

Originally posted by wardog wardog wrote:

Originally posted by metapsyborg22 metapsyborg22 wrote:

Not sure if this is related but I did the BIOS update, windows 10 started running and booting extremely slow. Reverted back to old bios and old working settings, still sluggish windows 10. Went through a bunch of other numerous "fixes" and landed on re-installing windows to fix. 

Again, not sure if its related to the bios update? Just wanted to post in case someone has a similar experience.

ab350 Fatal1ty K4


The BIOS itself wouldn't be responsible. Is your 10 fully updated?

And that's not me shucking the buck over onto MS either.

Too, there are variables like the mem used, that may have affected it "some' but not "extremely"

Checked memory usage and CPU, both were almost nothing. Uninstalled classic shell, still nothing. Windows ran like it was using up all the ram but it wasnt even touching 10%



No no no. Sry. Meant Make and Model.


Back to Top
wardog View Drop Down
Moderator Group
Moderator Group


Joined: 15 Jul 2015
Status: Offline
Points: 6447
Post Options Post Options   Thanks (0) Thanks(0)   Quote wardog Quote  Post ReplyReply Direct Link To This Post Posted: 19 Jul 2017 at 12:15pm
Originally posted by wardog wardog wrote:

Originally posted by metapsyborg22 metapsyborg22 wrote:

Originally posted by wardog wardog wrote:

Originally posted by metapsyborg22 metapsyborg22 wrote:

Not sure if this is related but I did the BIOS update, windows 10 started running and booting extremely slow. Reverted back to old bios and old working settings, still sluggish windows 10. Went through a bunch of other numerous "fixes" and landed on re-installing windows to fix. 

Again, not sure if its related to the bios update? Just wanted to post in case someone has a similar experience.

ab350 Fatal1ty K4


The BIOS itself wouldn't be responsible. Is your 10 fully updated?

And that's not me shucking the buck over onto MS either.

Too, there are variables like the mem used, that may have affected it "some' but not "extremely"

Checked memory usage and CPU, both were almost nothing. Uninstalled classic shell, still nothing. Windows ran like it was using up all the ram but it wasnt even touching 10%



No no no. Sry. Meant Make and Model.




Too, did you let Windows steady out and leet the processes settle down? ie: CPU cycles being consumed
Back to Top
 Post Reply Post Reply Page  <1 1213141516 23>
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 0.234 seconds.