ASRock.com Homepage
Forum Home Forum Home > Technical Support > Intel Motherboards
  New Posts New Posts RSS Feed - Asrock x99 Extreme 6 & Cooler ?
  FAQ FAQ  Forum Search Search  Events   Register Register  Login Login

Asrock x99 Extreme 6 & Cooler ?

 Post Reply Post Reply
Author
Message
RaylanG View Drop Down
Newbie
Newbie


Joined: 26 Apr 2015
Location: USA
Status: Offline
Points: 16
Post Options Post Options   Thanks (0) Thanks(0)   Quote RaylanG Quote  Post ReplyReply Direct Link To This Post Topic: Asrock x99 Extreme 6 & Cooler ?
    Posted: 26 Apr 2015 at 10:26pm
We're getting ready to put together our 1st PC build with the above board and Corsair H110 Hydro cooler.

The x99 extreme 6 mobo has a backplate already installed on the back of the motherboard. Is this backplate sufficient to hold the weight of the cooler or must other steps be taken to insure the integrity of the motherboard? We don't see how we can put a backplate on the board with the plate setup the way it is.

Our other question is about the breadboarding procedure, particularly the cooler. When we finally install the mobo and cooler in the tower, will repasting be necessary after running the hardware for just a few minutes? He intends on disconnecting the cooler from the CPU before installing it in the tower. TIA.
Back to Top
chosin View Drop Down
Newbie
Newbie
Avatar

Joined: 22 Apr 2015
Status: Offline
Points: 16
Post Options Post Options   Thanks (1) Thanks(1)   Quote chosin Quote  Post ReplyReply Direct Link To This Post Posted: 26 Apr 2015 at 11:23pm
with the x99 platform they have four threaded screw holes. you simply put your thermal paste on the processor spread it evenly, after its in the slot and retaining clips are secured down. They generally come with a cross bracket and thumb screws. so the back plate is not needed to be installed. after cooler is in place put the retaining bracket over cooler tighten the cooler down hand tight. when you turn on the system go straight to bios watch the temps for a little bit. YOU SHOULD ALWAYS ADD THERMAL PASTE TO IT UNLESS THE PAD IS ON IT ( I always remove the pad and put thermal paste on it )
2Evga For The Waste+970 gtHEX'S
ASRock X99X Killer
Creative Soundblaster Z
G.SKILL Ripjaws 4 series 16GB 4x4GB
DDR4 2400
Intel i7-5820K
Samsung 840
Crucial M100 512gb game drive
OS Win 8.1 64bit
Back to Top
parsec View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 04 May 2015
Location: USA
Status: Offline
Points: 4996
Post Options Post Options   Thanks (1) Thanks(1)   Quote parsec Quote  Post ReplyReply Direct Link To This Post Posted: 06 May 2015 at 12:30am
Your Corsair H110 provides the correct standoffs for mounting the water block/pump assembly to the 2011 socket. You'll find only one set of the four black standoffs will thread correctly into the threaded holes on the 2011 socket.

The instructions with the H110 shows the two different sets of mounting standoffs. The ones you must use have one of the threaded ends that is much shorter than the other, and has a larger diameter threaded stud than the longer threaded end.

Your X99 board has the 2011 v3 socket, which should have the same mounting characteristics as the earlier 2011 socket used on X79 boards.

You won't have any problems with weight or stress on the CPU socket, particularly when using the water block of any AIO liquid cooler. They are much lighter than any large standard CPU cooler.

You also won't need to apply thermal paste again or remount the water block, as long as you don't remove it from the CPU. If you remove the water block, you must clean off the old thermal paste from the CPU and water block, and apply new thermal paste.


Back to Top
RaylanG View Drop Down
Newbie
Newbie


Joined: 26 Apr 2015
Location: USA
Status: Offline
Points: 16
Post Options Post Options   Thanks (0) Thanks(0)   Quote RaylanG Quote  Post ReplyReply Direct Link To This Post Posted: 06 May 2015 at 9:16pm
Thanks so much for your help.

Yesterday we breadboarded our new build which necessitated hooking up the cooler to the CPU, the video card, SSD, PSU, etc.,  and did get a successful POST. You are correct about using the shorter standoffs. The overall installation went off w/o a hitch. We are using G.Skill Ripjaws DDR4 2666MHz. I do have to get into the BIOS and enable XMP. Geez, I was impressed to see just how cool the CPU was, 35C.

We did clean the paste from the CPU & cooler after dismantling the components to install in the tower. We did get our first look into UEFI BIOS. Our other PC's and laptops all run the standard non-UEFI. I may return for more help with setup because I never worked with that BIOS setup before. Today's BIOSes offer a lot more in configurability then previous ones.

Again, thanks for your help
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 0.156 seconds.