Print Page | Close Window

WakeOnLan not working J4205

Printed From: ASRock.com
Category: Technical Support
Forum Name: Intel Motherboards
Forum Description: Question about ASRock Intel Motherboards
URL: https://forum.asrock.com/forum_posts.asp?TID=14350
Printed Date: 17 Jun 2024 at 1:30am
Software Version: Web Wiz Forums 12.04 - http://www.webwizforums.com


Topic: WakeOnLan not working J4205
Posted By: Simon90
Subject: WakeOnLan not working J4205
Date Posted: 12 May 2020 at 12:04am
Hardware: [URL=https://www.asrock.com/mb/Intel/J4205-ITX/index.us.asp]J4205[/URL]

I tried to get WakeOnLAN startet, but when sending magic packages from my PC or my fritzbox (a router by avm, which can also send magic packages), the PC is still powered off.

The configuration seems ok:

$ sudo ifconfig enp1s0
enp1s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
        inet 192.168.1.35 netmask 255.255.255.0 broadcast 192.168.1.255
        inet6 2003:d1:73c:6800:dc8:cc91:3aa4:9563 prefixlen 64 scopeid 0x0<global>
        inet6 2003:d1:73c:6800:7285:c2ff:fe85:939f prefixlen 64 scopeid 0x0<global>
        inet6 fe80::7285:c2ff:fe85:939f prefixlen 64 scopeid 0x20<link>
        inet6 fe80::3e59:ce76:b7f8:2e02 prefixlen 64 scopeid 0x20<link>
        inet6 2003:d1:73c:6800:bcd5:ec31:627d:379b prefixlen 64 scopeid 0x0<global>
        inet6 2003:d1:73c:6800:4299:b7ff:831c:88fe prefixlen 64 scopeid 0x0<global>
        inet6 2003:d1:73c:6800:259f:6ff7:959a:888b prefixlen 64 scopeid 0x0<global>
        ether 70:85:c2:85:93:9f txqueuelen 1000 (Ethernet)
        RX packets 2064 bytes 555524 (542.5 KiB)
        RX errors 0 dropped 0 overruns 0 frame 0
        TX packets 2204 bytes 781779 (763.4 KiB)
        TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

:~$ sudo ethtool enp1s0
Settings for enp1s0:
        Supported ports: [ TP AUI BNC MII FIBRE ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes: 10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes: 10baseT/Half 10baseT/Full
                                             100baseT/Half 100baseT/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 100Mb/s
        Duplex: Full
        Port: MII
        PHYAD: 0
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: pumbg
        Wake-on: g
        Current message level: 0x00000033 (51)
                               drv probe ifdown ifup





Replies:
Posted By: Simon90
Date Posted: 12 May 2020 at 9:59pm
How can I check if the power supply supports WOL ?


Posted By: Algiux
Date Posted: 24 Jun 2023 at 12:51am
Enable WOL in UEFI, go to boot, boot from lan enable



Print Page | Close Window

Forum Software by Web Wiz Forums® version 12.04 - http://www.webwizforums.com
Copyright ©2001-2021 Web Wiz Ltd. - https://www.webwiz.net