CPU Compatibilty List
Printed From: ASRock.com
Category: Technical Support
Forum Name: AMD Motherboards
Forum Description: Question about ASRock AMD motherboards
URL: https://forum.asrock.com/forum_posts.asp?TID=25034
Printed Date: 03 Dec 2024 at 6:51am Software Version: Web Wiz Forums 12.04 - http://www.webwizforums.com
Topic: CPU Compatibilty List
Posted By: Tingman
Subject: CPU Compatibilty List
Date Posted: 25 Oct 2022 at 12:43pm
Hi, I have a Ryzen 5 5600 arriving tomorrow. It isn't on my motherboards cpu compatibility list but the similar 5600x is on the list. Do you think the 5600 will run or should I have gone with the 5600x?
AMD Ryzen 5 2600 Corsair 2x8 at 3200 ASROCk A320m HDV Rev. 4 Nvidia 3060ti
------------- D Tingman
|
Replies:
Posted By: wino
Date Posted: 25 Oct 2022 at 5:17pm
Ryzen 5xxx (Vermeer) is also not on my MB CPU Support List (Fatal1ty AB350 Gaming-ITX/ac). But there is the latest beta BIOS with AMD AM4 AGESA Combo V2 PI 1.2.0.7 in the BIOS section which I uploaded 2 weeks ago and I have a Ryzen 5 5600 working with no issues :)
------------- AB350 Gaming-ITX/ac 10.31 BIOS | Ryzen 5 5600 | G.Skill Flare X 2x8GB @ 3466 14-14-14-28 | Zotac GTX 1050 Ti | Kingston KC3000 1 TB M.2 | SilentiumPC Supremo M2 Gold 550W V2 | Plywood case 24x22x21 cm
|
Posted By: Tingman
Date Posted: 30 Oct 2022 at 12:07am
Thanks Wino. I'm using Bios 3.30 now, thinking I can go straight to 7.00 then to 7.2 before installation.?
------------- D Tingman
|
Posted By: ocen45
Date Posted: 30 Oct 2022 at 11:43pm
I am wondering too. Is it ok if we install 7.0 and 7.1 directly or do we need to install 6.xx versions first
|
Posted By: eccential
Date Posted: 31 Oct 2022 at 1:10am
Umm, 5600(100-000000927) is on the supported CPU list for A320M-HDV R4.0 It says BIOS P7.10 or later.
I'd say you first update to 7.00, and then 7.20 (I see no point going to 7.10), and THEN swap the CPU and boot again. I'd definitely use the in-BIOS flash function, rather than any software method.
The first boot with a new CPU will likely take a bit longer than usual.
|
Posted By: Lolalolita
Date Posted: 03 Nov 2022 at 3:36pm
Hey tingman.. Does it work properly on your a320m HDV r4 with ryzen 5 5600?? I need to know..
|
Posted By: DTingman
Date Posted: 04 Nov 2022 at 2:13pm
Not perfectly Lola. I can't seem to overclock my memory to 3200 like I could before. With the XMP Profile set to 3200, my computer crashes as soon as I start to game. I'm not sure of the cause as of yet.
|
Posted By: Lolalolita
Date Posted: 04 Nov 2022 at 5:50pm
Thanks for your information... I think your problem is just use recommended bios for 5 5600 .. Its 7.1 .. Try it and tell me what you got... ??
|
Posted By: DTingman
Date Posted: 05 Nov 2022 at 2:08am
Thanks Lola but I'm using Bios 7.2 and it is my understanding that I can't go backwards. It is a bummer because my memory is really slow now at 2133 I believe. I'm not sure Bios 7.1 would have been any different though.
|
Posted By: eccential
Date Posted: 05 Nov 2022 at 2:53am
I doubt there's any real difference between 7.1 and 7.2, as far as memory stuff is concerned.
It is strange to hear worse memory compatibility going from Zen+ to Zen3 CPU. Perhaps the firmware just lost something for an old RAM.
2133 is way too low, so definitely go into BIOS and manually tune some stuff. You don't even have to go that far. You almost can't lose, if your starting point is 2133 default.
|
Posted By: DTingman
Date Posted: 05 Nov 2022 at 6:19am
Tweaking the memory is all new to me. I did play around with it late last night a bit and it wouldn't boot up at all afterward so I had to pull the CMOS battery. Then it started right back up again at least.
|
Posted By: DTingman
Date Posted: 05 Nov 2022 at 12:06pm
My XMP 2.0 Profile 1 is DDR4-3200 16-18-18-36 at 1.35V. 2X8 set-up. Crucial Vengeance rated at 3200OC. Crashes quickly when gaming. Defaulted down to 2133 without XMP. Very sad...
|
Posted By: eccential
Date Posted: 05 Nov 2022 at 9:10pm
"Crucial Vengeance" Umm, Vengeance is Corsair brand. Crucial brand is Ballistix. Assuming it was just a minor brain fart, quick search found these unhappy people:
https://www.reddit.com/r/Amd/comments/qudvg3/is_corsair_vengeance_lpx_ram_bad_for_ryzen_5800x/" rel="nofollow - https://www.reddit.com/r/Amd/comments/qudvg3/is_corsair_vengeance_lpx_ram_bad_for_ryzen_5800x/
I never buy DIMMs if I don't know exactly what brand/die DRAM chips are being used. Corsair doesn't manufacture their own DRAM, so they grab whatever they can from the market. Easy enough for me to picky since I only buy ECC memory (Kingston Server Premier) LOL.
What's odd is that it worked fine with Zen+ CPU. I assume you didn't even remove the DIMMs when you swapped the CPU? If you did remove them, maybe remove them again, clean the contacts, and re-seat.
Also, if you're messing with it in BIOS, the first thing you need to do is to raise the voltage to 1.35V. Even if you can't reach 3200MT/s, something like 3000 would be pretty good.
|
Posted By: DTingman
Date Posted: 05 Nov 2022 at 11:20pm
Thanks Ecc. Yes, it is Corsair. I did actually re-seat them when I put the cpu cooler on but I didn't clean them. I'll play around with the timings a bit. One of posts on that Reddit link had the same memory running at 3800 but yes, I'd be happy ok with 3000.
|
Posted By: Vedandre
Date Posted: 06 Nov 2022 at 1:07am
Good afternoon. Why is there no amd a8 7680 (ad7680aci43ab) in the compatibility list for asrock fm2a78m pro4+ motherboard. Although the processors are newer. Does anyone have information on this?
|
Posted By: cx5
Date Posted: 07 Nov 2022 at 2:58pm
Hi @DTingman
you need this solution, short quick consice answer = http://www.my-acoustic.com/images/GirdMstr75.jpg" rel="nofollow - http://www.my-acoustic.com/images/GirdMstr75.jpg
long full details = https://forum.asrock.com/forum_posts.asp?TID=24829&title=xml-profile-2-0-not-working-with-ram" rel="nofollow - https://forum.asrock.com/forum_posts.asp?TID=24829&title=xml-profile-2-0-not-working-with-ram
good luck.
------------- x370taichi@3.50gen4 AX750 Optane900P SN770 3800x PosdonZro4 BarrowPWM-17w>420x140x28 XFX SWFT319 6900XT MSI RX560 LP to get Fluid Motion BlueskyFRC 75hz
|
Posted By: DTingman
Date Posted: 09 Nov 2022 at 3:03am
Thanks CX5. You were correct that the Secondary timings didn't seem to change when I set the XMP profile so I plugged those in manually, but it still doesn't run stable anywhere near 3200. The only thing I've done so far that helped was without the XMP profile, upping the voltage to 1.25 and that seems to allow me to run stable at 2667.
|
Posted By: cx5
Date Posted: 09 Nov 2022 at 9:27am
Hi @DTingman,
getting the secondaries is only part of it, if you read all the posts replies & history in the links and the link's links I've given then you would have seen CLDO_VDDP, which is not the regular simple VDDP alone, they are two completely different thing, you will have to dig into the bios everywhere to find it. Back in 2017 /2018 the CLDO_VDDP was put very deep and default 0.7v hence most XMP failed. Nowadays it's right_UNDER_inside of the SOC voltages area on the tweaker page, you'll have to dig in deep. You need 1 volt for CVLDO_VDDP, recent ASRock bios some versions default to 0.95v which partly works and don't. This CLDO_VDDP has something to do with infinity fabric, the faster it runs the more voltages it requires, my 3600 needs 1 volt, when 0.95v will sometimes crash game.
btw, what is your full spec?
also please provide a zentiming screen capture, it is extremely important to see VSOC and CLDO_VDDP, etc etc etc...
keep the bios agesa 1.2.0.7
try 1.4v dram
more voltages here https://forum.asrock.com/forum_posts.asp?TID=24829&PID=100979&title=xml-profile-2-0-not-working-with-ram#100979" rel="nofollow - https://forum.asrock.com/forum_posts.asp?TID=24829&PID=100979&title=xml-profile-2-0-not-working-with-ram#100979
------------- x370taichi@3.50gen4 AX750 Optane900P SN770 3800x PosdonZro4 BarrowPWM-17w>420x140x28 XFX SWFT319 6900XT MSI RX560 LP to get Fluid Motion BlueskyFRC 75hz
|
Posted By: DTingman
Date Posted: 10 Nov 2022 at 1:21pm
Hey CX-5. This is an entry level store bought gaming computer I bought a couple years ago and have done a few upgrades on. The motherboard and power supply may be holding me back but below are my specs. I did made a copy of my Zentimings report but haven't figured out how to post it here yet.
AMD Ryzen 5 5600 Nvidia GForce RTX 3060Ti Corsair Vengeance LPX 3200OC 2x8 Asrock a320 HDV Rev 4.0 motherboard Bios ver. 7.2 Generic 600 watt power supply 2 SSD drives and 1 SATA hard drive
|
Posted By: cx5
Date Posted: 10 Nov 2022 at 3:25pm
Hello @DTingman,
Actually if you achieve boot 3200 xmp and windows stable, games no crash, etc, then no need to post anything to me....
all the tips are at the other posts started by GrdMstr79, your situation nearly same as his. Make sure to read the entire history, all of it, you'll need all of it. Pay extra attention to this https://forum.asrock.com/forum_posts.asp?TID=24829&PID=101680&title=xml-profile-2-0-not-working-with-ram#101680" rel="nofollow - https://forum.asrock.com/forum_posts.asp?TID=24829&PID=101680&title=xml-profile-2-0-not-working-with-ram#101680
I also have A320_HDV for my sister. Apart from no pcie4 and no storemi, I don't think you're loosing anything else.
Certainly not being held back by A320 and 600watts. It's good enough.
When I game 1440p ultra high settings, my 3800x only pulls 60 watts and my 6900XT only pulls between 100~150 watts, because I use Radeon Chill fps limits to 100fps, I don't see any point to waste more power.
------------- x370taichi@3.50gen4 AX750 Optane900P SN770 3800x PosdonZro4 BarrowPWM-17w>420x140x28 XFX SWFT319 6900XT MSI RX560 LP to get Fluid Motion BlueskyFRC 75hz
|
Posted By: DTingman
Date Posted: 11 Nov 2022 at 1:02pm
Games do crash CX at any memory speeds faster than 2667. Just had a beautiful flight around Rio at sunset in MS Flight Simulator at 2667, which is my main goal in this search...but hopeful that I can get the memory up to it's xmp rated speed 3200.
|
Posted By: DTingman
Date Posted: 11 Nov 2022 at 1:05pm
Anybody that has any insight into this endeavor, please chime in. I thank you in advance.
|
Posted By: bjlockie
Date Posted: 11 Nov 2022 at 1:11pm
Is it only games that crash? Try a memory stress test: https://memtest.org/" rel="nofollow - https://memtest.org/
------------- ASRock B450M Pro4 16 GB DDR4, 500 watt PS, AMD Ryzen-5 5600, NVidia GTX-1050, 5.70 BIOS
|
Posted By: DTingman
Date Posted: 11 Nov 2022 at 2:01pm
Correct, seems as if I can play youtube all night at 2667 on auto., but MSFS would benefit considerably from a faster memory speed.
|
Posted By: DTingman
Date Posted: 11 Nov 2022 at 2:30pm
Strangely, my Ryzen 5 5600 seems to flutter between running at 3600 and 4450 while running youtube, a tad fast according to spec,,?
|
Posted By: cx5
Date Posted: 11 Nov 2022 at 2:58pm
DTingman wrote:
Games do crash CX at any memory speeds faster than 2667. Just had a beautiful flight around Rio at sunset in MS Flight Simulator at 2667, which is my main goal in this search...but hopeful that I can get the memory up to it's xmp rated speed 3200. |
need to see your zentiming screenshots to check many many parameters in order to diagnose problem.
https://zentimings.protonrom.com/" rel="nofollow - https://zentimings.protonrom.com/
no zentming screenshot = no way to help you.
------------- x370taichi@3.50gen4 AX750 Optane900P SN770 3800x PosdonZro4 BarrowPWM-17w>420x140x28 XFX SWFT319 6900XT MSI RX560 LP to get Fluid Motion BlueskyFRC 75hz
|
Posted By: DTingman
Date Posted: 11 Nov 2022 at 3:43pm
Sorry to be such a newbie CX, but could you explain to me how to post my zentimings? I do have them.
|
Posted By: cx5
Date Posted: 11 Nov 2022 at 4:29pm
try this https://imgbb.com/" rel="nofollow - https://imgbb.com/
or various photo hosting website .....
or simply upload as a file, we could download and view it. It's not about viewing in this forum page, hence as long as we can provide a link to download it is also OK.
else write all the things down by hand :) personally I wouldn't, too easy to slip in a mistake when typing so many similar parameters.....
------------- x370taichi@3.50gen4 AX750 Optane900P SN770 3800x PosdonZro4 BarrowPWM-17w>420x140x28 XFX SWFT319 6900XT MSI RX560 LP to get Fluid Motion BlueskyFRC 75hz
|
Posted By: DTingman
Date Posted: 12 Nov 2022 at 12:06pm
After crashing a number of times at XMP, I've gotten my ram up to 2800 using the timings in the xmp profile and running it at 1.28 Mhz volts. Runs Microsoft Flight Simulator quite well in ultra. Would be nice to at least get 3000 though. Next step is messing with voltages of the memory controller I'm thinking...
AMD Ryzen 5 5600 Nvidia GForce RTX 3060ti Asrock a320 HDV R.4 Bios 7.2 Corsair Vengeance 32000C 2x8
|
Posted By: eccential
Date Posted: 12 Nov 2022 at 9:25pm
Is there any reason you're not going straight to 1.35V ??
I don't know exactly which Vengeance model you have, since there are so many, and it probably isn't even that important because Corsair would just use whatever brand it can buy for cheap (Samsung/Micron/SKHynix/...).
But one of the specs for a 8GB Vengeance model I found on Corsair's own page says 2133 15-15-15-36 1.2V (base) and 3200 16-20-20-38 1.35V.
|
Posted By: DTingman
Date Posted: 13 Nov 2022 at 12:18am
Yes eccential, it boots fine but crashes while gaming at 1.35v.
|
Posted By: DTingman
Date Posted: 13 Nov 2022 at 2:11pm
Tried another set of what was locally available RAM this afternoon, a set of 2x16 loosely timed Corsair 3200's. Same problem. Booted up, but crashed quickly before MSFS even started. Got to be the memory controller...
|
Posted By: DTingman
Date Posted: 14 Nov 2022 at 3:57am
Best I can get so far to run stable is 2800 at 1.28V while using the XMP Profile timings of 16-18-18-36-54. Anybody have any suggestions?
|
Posted By: DTingman
Date Posted: 14 Nov 2022 at 10:27am
To update, my A320m HDV Rev4 Bios 7.2 now seems to be running stably with my now 2x16 Corsair memory at 2993. My Ryzen 5 5600 is starting to cooperate as well.
|
Posted By: Xaltar
Date Posted: 14 Nov 2022 at 5:19pm
Thanks for the update DTingman.
-------------
|
Posted By: DTingman
Date Posted: 15 Nov 2022 at 7:26am
Had a crash while gaming today so I lowered my Ram Speed to 2867 and it's voltage to 1.28. Running stably while gaming so far. Higher speeds and or volts crash. The inexpensive and locally available Corsair 2x16's are already loosely timed but I'd love them to get up to their XMP rated speed of 3200. Any suggestions on how to get more out of these? These are my zentimings: https://imgur.com/n9NDTVu" rel="nofollow - https://imgur.com/n9NDTVu
|
Posted By: cx5
Date Posted: 15 Nov 2022 at 9:36am
DTingman wrote:
Had a crash while gaming today so I lowered my Ram Speed to 2867 and it's voltage to 1.28. Running stably while gaming so far. Higher speeds and or volts crash. The inexpensive and locally available Corsair 2x16's are already loosely timed but I'd love them to get up to their XMP rated speed of 3200. Any suggestions on how to get more out of these? These are my zentimings: https://imgur.com/n9NDTVu" rel="nofollow - https://imgur.com/n9NDTVu
|
OK, this is a good start, next please show us the zentiming when you manage to boot into windows running 2933. We need to check many other things when it is in 2933 to find out what crash.
------------- x370taichi@3.50gen4 AX750 Optane900P SN770 3800x PosdonZro4 BarrowPWM-17w>420x140x28 XFX SWFT319 6900XT MSI RX560 LP to get Fluid Motion BlueskyFRC 75hz
|
Posted By: DTingman
Date Posted: 15 Nov 2022 at 10:49am
Hey again cx. Windows wouldn't fully load with 2933 @ 1.28V so I upped it to 1.29V. Below are the new zentimings. https://imgur.com/w7Ynfad" rel="nofollow - https://imgur.com/w7Ynfad
|
Posted By: cx5
Date Posted: 15 Nov 2022 at 2:23pm
DTingman wrote:
Hey again cx. Windows wouldn't fully load with 2933 @ 1.28V so I upped it to 1.29V. Below are the new zentimings. https://imgur.com/w7Ynfad" rel="nofollow - https://imgur.com/w7Ynfad
|
OK your problem is ASRock's bios didn't setup the many correct voltageseses for you....
Hence now you will need to set them manually.
I already given LINKS and replies to you regarding the voltages that you need, did you not read them?
Or you didn't understand them? >OK fine, so I highlight them to you again. >>Please make sure to read them this time and compare to your zentiming screen capture the many parameterssss.
FIRST REPLY _________________________________________________ Posted: 07 Nov 2022 at 2:58pm
cx5 wrote:
Hi @DTingman
you need this solution, short quick consice answer = http://www.my-acoustic.com/images/GirdMstr75.jpg" rel="nofollow - http://www.my-acoustic.com/images/GirdMstr75.jpg
long full details = https://forum.asrock.com/forum_posts.asp?TID=24829&title=xml-profile-2-0-not-working-with-ram" rel="nofollow - https://forum.asrock.com/forum_posts.asp?TID=24829&title=xml-profile-2-0-not-working-with-ram
THEN You replied on Posted: 09 Nov 2022 at 3:03am
DTingman wrote:
Thanks CX5. You were correct that the Secondary timings didn't seem to change when I set the XMP profile so I plugged those in manually, but it still doesn't run stable anywhere near 3200. The only thing I've done so far that helped was without the XMP profile, upping the voltage to 1.25 and that seems to allow me to run stable at 2667. | good luck. | giving the impression you understand secondaries timing - means should have enough skill to understand the other parameters too (including voltageseseseses), but I'm surprised you didn't see all the voltageses required???
On Posted: 09 Nov 2022 at 9:27am
cx5 wrote:
Hi @DTingman,
getting the secondaries is only part of it, if you read all the posts replies & history in the links and the link's links I've given then you would have seen CLDO_VDDP, which is not the regular simple VDDP alone, they are two completely different thing, you will have to dig into the bios everywhere to find it. Back in 2017 /2018 the CLDO_VDDP was put very deep and default 0.7v hence most XMP failed. Nowadays it's right_UNDER_inside of the SOC voltages area on the tweaker page, you'll have to dig in deep. You need 1 volt for CVLDO_VDDP, recent ASRock bios some versions default to 0.95v which partly works and don't. This CLDO_VDDP has something to do with infinity fabric, the faster it runs the more voltages it requires, my 3600 needs 1 volt, when 0.95v will sometimes crash game.
btw, what is your full spec?
also please provide a zentiming screen capture, it is extremely important to see VSOC and CLDO_VDDP, etc etc etc...
keep the bios agesa 1.2.0.7
try 1.4v dram
more voltages here https://forum.asrock.com/forum_posts.asp?TID=24829&PID=100979&title=xml-profile-2-0-not-working-with-ram#100979" rel="nofollow - https://forum.asrock.com/forum_posts.asp?TID=24829&PID=100979&title=xml-profile-2-0-not-working-with-ram#100979 |
everything is written to you in above, did you not read it? or which/what part you don't understand?
>>>>>>> try 1.4v dram <<<<<<<< why didn't you do this ????
_____________________________________
even @eccential told you to run 1.35v but why don't you run it???? Posted: 12 Nov 2022 at 9:25pm
eccential wrote:
Is there any reason you're not going straight to 1.35V ??
I don't know exactly which Vengeance model you have, since there are so many, and it probably isn't even that important because Corsair would just use whatever brand it can buy for cheap (Samsung/Micron/SKHynix/...).
But one of the specs for a 8GB Vengeance model I found on Corsair's own page says 2133 15-15-15-36 1.2V (base) and 3200 16-20-20-38 1.35V.
|
___________________________________
and you replied
DTingman wrote:
Yes eccential, it boots fine but crashes while gaming at 1.35v. |
because you didn't set ALL the OTHER voltagesESESEES hence crash.
which I've repeatedly given you in above links and written text.
Hope you realized and manages to catch them this time.
------------- x370taichi@3.50gen4 AX750 Optane900P SN770 3800x PosdonZro4 BarrowPWM-17w>420x140x28 XFX SWFT319 6900XT MSI RX560 LP to get Fluid Motion BlueskyFRC 75hz
|
Posted By: DTingman
Date Posted: 16 Nov 2022 at 5:45am
Ok, I had tried those voltages with my first set of memory and it didn't help so I had left them on Auto on this new set of 2x16's, which so far I've done slightly better with on speeds. The secondary timings are there. I've now updated to the recommended voltages. It now crashes before a game(MSFS) fully loads. These are the updated zentimings. I also tried running the memory at 1.4V and that crashed even sooner. If I missed any settings let me know. https://imgur.com/a/OB4Dq6L" rel="nofollow - https://imgur.com/a/OB4Dq6L
|
Posted By: cx5
Date Posted: 16 Nov 2022 at 11:35am
Hi @DTingman,
Ok, you've done well, those voltages, don't lower, can be higher a bit to get stability.
URGENT, please check your dram voltage actual used???, often it is lower than expected, i.e. we key in 1.35v in bios but actual running is 1.33v, that's why I ask you to run 1.4v. I use ASRock's A-Tuning software to check, Or quick check in bios HARDWARE/monitoring page. Make sure you have 1.37v or more actual running because you have 4_faces = 4_ranks in total of IC/chip/ram need a bit more voltage. >After voltage is ensured 1.37v or more.
Then next Quick and Dirty attempts = change procODT from 48ohms up each step and test game. i.e. 53ohms if fail than up to 60ohms if fails then so and so forth up to max 80ohms. I've not tried higher than 80ohms.
I've got CMK32GX4M2B3000C15 hynix-chip A-die and does POST with agesa 1.2.0.7 which you also run. My ram used to be good with some older agesa=older bios. Some bios 100% compatible, some not.
but the good news is that 1usmus's Dram Calculator ver 1.7.3 manages to provide close to/near suitable values for it to work with 1.2.0.7 (lucky). Not always the calculator gets right, hence it's just a 90% ball park guide, then we need to manually change values and test to get 100%.
your CMK32GX4M2E32000C16 is Micron-chip D-die see link https://www.overclock.net/threads/new-dram-calculator-for-ryzen%E2%84%A2-1-7-3-overclocking-dram-on-am4-membench-0-8-dram-bench.1640919/post-28630941" rel="nofollow - https://www.overclock.net/threads/new-dram-calculator-for-ryzen%E2%84%A2-1-7-3-overclocking-dram-on-am4-membench-0-8-dram-bench.1640919/post-28630941
lets run a simple memory performance test to find out the variousesese latencieseses and how many errors, etc. In the future you can make small changes to timing and run test to find out if the error has reduced. Download link = https://www.overclock.net/threads/new-dram-calculator-for-ryzen%E2%84%A2-1-7-3-overclocking-dram-on-am4-membench-0-8-dram-bench.1640919/" rel="nofollow - https://www.overclock.net/threads/new-dram-calculator-for-ryzen%E2%84%A2-1-7-3-overclocking-dram-on-am4-membench-0-8-dram-bench.1640919/
side info = https://www.techpowerup.com/review/amd-ryzen-memory-tweaking-overclocking-guide/" rel="nofollow - https://www.techpowerup.com/review/amd-ryzen-memory-tweaking-overclocking-guide/
click on membench and run the "EASY" test. Get results like this http://www.my-acoustic.com/images/3333%20memtest%20PASS%2071ns%20141second%2016-18-18-18-40-60-480-357-219.png" rel="nofollow - http://www.my-acoustic.com/images/3333%20memtest%20PASS%2071ns%20141second%2016-18-18-18-40-60-480-357-219.png
screen capture the membench results together with zentiming and ASRock's MB voltages and show us again, with these many information, may be more people can help you too.
------------- x370taichi@3.50gen4 AX750 Optane900P SN770 3800x PosdonZro4 BarrowPWM-17w>420x140x28 XFX SWFT319 6900XT MSI RX560 LP to get Fluid Motion BlueskyFRC 75hz
|
|