ASRock B650M PG Riptide
Printed From: ASRock.com
Category: Technical Support
Forum Name: AMD Motherboards
Forum Description: Question about ASRock AMD motherboards
URL: https://forum.asrock.com/forum_posts.asp?TID=25949
Printed Date: 30 Jul 2025 at 2:38am
Software Version: Web Wiz Forums 12.04 - http://www.webwizforums.com
Topic: ASRock B650M PG Riptide
Posted By: hansk85
Subject: ASRock B650M PG Riptide
Date Posted: 30 May 2023 at 2:18pm
|
Hi all, I'm experiencing random bluescreen crashes after swapping to this motherboard and with a new CPU and GPU. I have updated the firmware/bios, and installed the latest chipset drivers for Wwindows 11. Running the default configuration in the bios apart from disabling the HD audio. I've had maybe 4-5 different BSOD error messages, but they appear to only happen just after booting my computer when its been turned off for a few hours and the launching a youtube video and a computer game. Any chance the crashes could be related to the pc parts being cold, or any other theory? When I boot up the pc after the initial crash, i am able to run CPU/GPU/Memory stresstest applications without any crashes. The only other problem i have noticed is crackling in the usb headset, but not sure if that is related. |
Replies:
Posted By: Xaltar
Date Posted: 30 May 2023 at 3:40pm
|
A few things of note: 1. If you didn't perform a fresh Windows installation, residual drivers and software can cause BSODs. 2. If you used the same old PSU it could be dying, issues on cold boot can indicate the components are worn out and need to be up to temp before it stabilizes. Given you are also getting crackling in your USB headset, that could also be caused by bad power, I would start by trying another PSU. Good luck  ------------- 
|
Posted By: hansk85
Date Posted: 30 May 2023 at 4:01pm
|
Thanks for the quick reply. The Windows installation is fresh, and I already replaced my old PSU with a "MSI MPG A1000G PCIE5 1000W" because of the power requirements on the GPU (7900 XTX). The only parts i didnt replace was my harddrives and CPU fan. Id rather not buy a new PSU just to test, do you think it would be worth changing around which connections points on the PSU i use? |
Posted By: Xaltar
Date Posted: 30 May 2023 at 4:13pm
|
It's worth a try. Make sure to install all the latest drivers for the new hardware. A fresh Windows install may also help. You can try on a spare drive so you don't have to reinstall all your software again if it doesn't help. -------------
|
Posted By: cx5
Date Posted: 01 Jun 2023 at 2:13pm
|
sounds like not enough SOC voltage and/or infinity fabric voltageseses, so many terms, one of them is CLDO_VDDP, and may be MEM_VDD, VPP, VDDQ, VDD_MISC, these are critical to DDR5 stability in order not to experience sudden BSOD, also because vdrrop. If possible, please download zentiming and show us a screen catpure. Download from https://zentimings.protonrom.com/" rel="nofollow - https://zentimings.protonrom.com/ example of zentimig and zen4 users = https://www.overclock.net/threads/asrock-x670e-taichi-taichi-carrara-overclocking-discussion-thread.1801259/page-41" rel="nofollow - https://www.overclock.net/threads/asrock-x670e-taichi-taichi-carrara-overclocking-discussion-thread.1801259/page-41 would be helpful if you can also list ram spec, running EXPO or XMP or not at all, etc etc..... CPU PBO still a thing for zen4??? then CO = curve optimizer being used? ------------- x370taichi@3.50gen4 AX750 Optane900P SN770 3800x PosdonZro4 BarrowPWM-17w>420x140x28 XFX SWFT319 6900XT MSI RX560 LP to get Fluid Motion BlueskyFRC 75hz |