ASRock X99 WS-E/10G memory problem
Printed From: ASRock.com
Category: Technical Support
Forum Name: Intel Motherboards
Forum Description: Question about ASRock Intel Motherboards
URL: https://forum.asrock.com/forum_posts.asp?TID=4328
Printed Date: 22 Dec 2024 at 7:18pm
Software Version: Web Wiz Forums 12.04 - http://www.webwizforums.com
Topic: ASRock X99 WS-E/10G memory problem
Posted By: larry
Subject: ASRock X99 WS-E/10G memory problem
Date Posted: 31 Jan 2017 at 12:01am
|
" rel="nofollow - I have motherboard asrock e ws 10g with intel core I7 5960x haswell and G. SKILL Ripjaws 4 Series 128GB (8 x 16GB) 288- Pin DDR4 SDRAM DDR4 2400 (PC4 19200) Intel X99 Platform Extreme Performance Memory Kit Model F4- 2400C14Q2- 128GRK, 6x WD Gold 8TB Datacenter Hard Disk Drive - 7200 RPM Class SATA 6 Gb/s 128MB Cache 3.5 Inch - WD8002FRYZ, 2x nvidia titan x pascal sli. problem: 1. bios 3.40 no detect 128gb memory (detect 96gb); 2. raid failure :( 3. windows 10 pro WHEA-UNCORRECTABLE-ERROR How to solve problem ? ------------- [IMG] http://example.com/smiley.gif [/ IMG] |
Replies:
Posted By: wardog
Date Posted: 31 Jan 2017 at 2:48am
|
We'll go from there on to testing your memory sticks individually. |
Posted By: wardog
Date Posted: 31 Jan 2017 at 2:57am
" rel="nofollow -
When you say it doesn't detect all 128GB, is this with running at their initial JEDEC timings associated with JEDEC 2133 initial posting speed? Or is this after you either set them up manually or used XMP to set them to their "rated' 2400? Also, and I don't know how much this may affect you there yet G.Skill does not list this kit as compatible. More on that after learning the above I ask. |
wardog wrote:Posted By: larry
Date Posted: 31 Jan 2017 at 4:27am
|
Before it was 128, but after I cleared it, it detects 96,. I did Try setting the memory speed to 2133 as a test. Also set all the memory timings to Auto. Find the MRC Fast Boot option in the DRAM Configuration screen, usually at the very bottom. Set it to Disabled, to allow memory training to occur during POST. POST will be longer, so start up time will be longer. ------------- [IMG] http://example.com/smiley.gif [/ IMG] |
Posted By: wardog
Date Posted: 31 Jan 2017 at 8:46am
|
Here's what I'd like you to do. 1. Power down, turn the PSU off, press and hold the cases Power button for 5secs, then remove the power cord from the PSU 2. Remove all eight sticks of memory 3. Clear the BIOS 4. Using the picture below place two sticks ONLY into mem slots B1 and D1 5. Re-apply power and boot it into the BIOS 6. These sticks will automatically boot to the JEDEC Standard speed of 2133, as G.Skill has programmed them to behave. 6a. If these two sticks do not show in the BIOS as 2133, stop here and post back. Otherwise continue following on...... 7. Here now while still in the BIOS with these two sticks running 2133, choose/select the XMP Profile Setting to/of 2400, don't do anything else, go to the Save and Exit, Save and Exit, letting it reboot and then head directly back into the BIOS to verify that these two sticks did indeed boot up at 2400. If not, stop here and post back. Otherwise continue following on...... 8. Good. These two booted at 2400. 9. Now power down and unplug the PSU from the wall. 10. Now insert the remaining 6 sticks, making sure they are firmly seated in the memory slots. 11. Apply power and fingers crossed bott her up and head straight away into the BIOS. If yo u got to here w/o stopping on the previous steps please take the time to thank an anonymous poster( I forget who exactly, but credits non the les) that had discovered this means/method to get all eight sticks running on their XMP settings/timings. Sigh....... If not post back  |
Posted By: larry
Date Posted: 31 Jan 2017 at 9:16pm
|
memory ddr4_A1, ddr4_A2 no detect :( ------------- [IMG] http://example.com/smiley.gif [/ IMG] |
Posted By: wardog
Date Posted: 31 Jan 2017 at 9:37pm
" rel="nofollow -
Is this with all eight sticks installed after following the steps I posted? |
Posted By: larry
Date Posted: 31 Jan 2017 at 9:54pm
|
yes ------------- [IMG] http://example.com/smiley.gif [/ IMG] |
Posted By: parsec
Date Posted: 31 Jan 2017 at 10:15pm
|
Have you tried increasing the DRAM voltage? Try at least 1.25V even at 2133. Try using the System Agent Voltage Offset option in the FIVR Configuration screen, adding 0.05V. G.SKILL does not show your model of memory as compatible with any ASRock X99 board for some reason. Click on the QVL tab: http://www.gskill.com/en/product/f4-2400c14q2-128grk" rel="nofollow - http://www.gskill.com/en/product/f4-2400c14q2-128grk What RAID failure do you have? How many drives in what type of RAID array? All six of the WD Gold drives? ------------- http://valid.x86.fr/48rujh" rel="nofollow"> 
|
Posted By: wardog
Date Posted: 31 Jan 2017 at 10:37pm
Ahhh, parsec has arrived. larry, you are now in better hands than mine concerning X99 boards. parsec has gobs of X99 experience. |
Posted By: larry
Date Posted: 31 Jan 2017 at 11:07pm
After installing windows 10 pro, pc restarts, but in the raid screen, it says raid fails in red, not bootable.
All the raid gives that message.
This giving blue screen of windows 10 error code 0xc0000001
File \ windows \ syste32 \ drivers \ pcw.sys------------- [IMG] http://example.com/smiley.gif [/ IMG] |
Posted By: larry
Date Posted: 31 Jan 2017 at 11:10pm
|
system agent voltage offset min: -0.300v max: 0.500v ------------- [IMG] http://example.com/smiley.gif [/ IMG] |
Posted By: larry
Date Posted: 31 Jan 2017 at 11:13pm
|
I put it -0,300v, now it does not turn on ------------- [IMG] http://example.com/smiley.gif [/ IMG] |
Posted By: larry
Date Posted: 02 Feb 2017 at 3:04am
|
I got \o/\o/ all memory detect and raid is ok :) Thank you for your help ^^ ------------- [IMG] http://example.com/smiley.gif [/ IMG] |