Print Page | Close Window

AB350 Gaming K4 | BIOS update not working

Printed From: ASRock.com
Category: Technical Support
Forum Name: AMD Motherboards
Forum Description: Question about ASRock AMD motherboards
URL: https://forum.asrock.com/forum_posts.asp?TID=5222
Printed Date: 23 Dec 2024 at 7:39am
Software Version: Web Wiz Forums 12.04 - http://www.webwizforums.com


Topic: AB350 Gaming K4 | BIOS update not working
Posted By: terosterone
Subject: AB350 Gaming K4 | BIOS update not working
Date Posted: 25 May 2017 at 6:14pm
" rel="nofollow -

Hi,

I'm looking for some help troubleshooting my bios update issue.  
I'm trying to update my motherboard's bios from 1.30 to the new 2.50 bios.

The bios 1.30 version does not have instant flash, so updating from DOS is the only option.


I am following this guide from Asrock:  http://www.asrock.com/support/BIOSIG.asp?cat=DOS8 

I finish step 4, but instead going to step 5 (the BIOS updating), I get booted back to DOS or my Windows installation, depending on which primary bootdrive I choose. 

Does anyone have a clue as to what could be causing this issue?


So far I've tried:
  • Creating a pendrive version of both FreeDOS and MS DOS 98.  
  • Updating to both 1.4 and 2.5. 
  • Made the pendrive my dafult boot drive
  • Disconnected my windows drive.  
  • Each time I get the same dialogue in DOS as the guide does (https://imgur.com/a/DHPgA#KpduBbC)


  • Thanks in advance.



Replies:
Posted By: ronniedude
Date Posted: 25 May 2017 at 10:14pm
" rel="nofollow - That link appears to be broken for me, can I see if you can get an updated link to that guide so we can see what you're trying to do through the steps?


Posted By: Nightbird
Date Posted: 25 May 2017 at 10:32pm
" rel="nofollow - Hi,
So, if you "press any key to continue", that doesn't work ?

Did you try to load the default settings ?

Don't know if that can help :
https://www.youtube.com/watch?v=PbyB-drELXE


Posted By: terosterone
Date Posted: 26 May 2017 at 1:08am
The link itself works, but for some reason the hyperlinking breaks it. 
I removed the hyperlink, so if you just copypaste the link to a browser, it should work.  
It's the motherboards BIOS (DOS) guide. 


Posted By: terosterone
Date Posted: 26 May 2017 at 1:08am
Hi @Nightbird,
Yes and Yes. 
After any key, it doesn't "automatically update the bios," as said in the video :( 


Posted By: am4lurker
Date Posted: 26 May 2017 at 1:17am
" rel="nofollow - After "pressing any key", it will reboot and go to Post screen right? Have you tried to press F2 so it goes to the BIOS?


Posted By: terosterone
Date Posted: 26 May 2017 at 1:26am
Yes. 
I've pressed F2 to get back into the UEFI. The version doesn't update and stays at 1.30. 
Even if I reset settings to default and reboot. 


Posted By: Nightbird
Date Posted: 26 May 2017 at 5:18am
" rel="nofollow - At the prompt, do you type
c:\>biosname.exe


ideas :
the volume of your usb pen drive ? i see on the video "volume in drive C 4 GB"

enable Legacy Boot and disable Secure Boot



Posted By: terosterone
Date Posted: 26 May 2017 at 4:57pm
I type the biosname without .exe.
I will try enabling legacy boot and disabling secure boot.
Edit: Legacy boot was enabled and secure boot was disabled by default.
I tried typing biosname.exe and it didn't work either.



Posted By: Nightbird
Date Posted: 26 May 2017 at 7:39pm
About the bios name, do you type
AB35G4_250.exe
or
AB35G4~1.exe


Posted By: terosterone
Date Posted: 27 May 2017 at 12:18am
I type AB35G4~1.exe
I tried AB35G4_250, but it didn't work.


Posted By: jers
Date Posted: 28 May 2017 at 6:53am
I have the same issue Asrock fatal1ty X370 K4 gaming bios v1.30

I boot to dos disk just fine, i run the executable, i see all the expected messages (finding model, copying file, setting environement variable) ... then i see press any key to reboot , i press a key and it reboots but it does not update anything ie i do not see the update process like in the guide.

I tried clearing BIOS setting and loading default UEFI value but it did nothing.

I want to stress again issue is not with booting to DOS or running the DOS upgrade executable, on that front no issue, it just doesn't do anything

I am bit loss on what to try next


Posted By: terosterone
Date Posted: 28 May 2017 at 6:39pm
Right here with you man Cry

I can't even OC from the BIOS with such an old bios version..

Not quite sure this would even fall under the RMA category tbh,  
the issue would just be pinned on the user.

Hopefully someone can provide us with an answer!



Print Page | Close Window

Forum Software by Web Wiz Forums® version 12.04 - http://www.webwizforums.com
Copyright ©2001-2021 Web Wiz Ltd. - https://www.webwiz.net