Help with h110 btc+ no boot
Printed From: ASRock.com
Category: Technical Support
Forum Name: Intel Motherboards
Forum Description: Question about ASRock Intel Motherboards
URL: https://forum.asrock.com/forum_posts.asp?TID=6508
Printed Date: 25 Apr 2024 at 8:02pm
Software Version: Web Wiz Forums 12.04 - http://www.webwizforums.com
Topic: Help with h110 btc+ no boot
Posted By: EdS
Subject: Help with h110 btc+ no boot
Date Posted: 06 Nov 2017 at 8:38am
|
" rel="nofollow - Hello all.. any help would be appreciated.. I;ve tried everything, and am getting nowhere.. I have the mining board H110 BTC+, and have it set up with evga 1300 G2. I have followed the mining set up PDF, and installed the following: CPU I3 7100 8 gb RAM PSU evga 1300 G2 5 GTX 1070's on powered risers. Problem is, the board will not boot. I ran power as directed to Molex pins.. 8 pin board ATX, 24 pin, and board SATA as illustrated in PDF. I have swapped out CPU's.. I have changed RAM, RAM slots, I have tested PSU.. but when you hit the small power button on the MoBo, you hear a small click from the PSU, and nothing. Only sign that there is power is small yellow light blinking on ethernet cable housing. There is no sign of a short.. or other issue. The board doesn't so anything... thoughts? |
Replies:
Posted By: parsec
Date Posted: 06 Nov 2017 at 10:08am
It sounds like the PSU is not starting due to a fault of some kind, the click possibly being a protective relay. Where/how is the board mounted? On some kind of open frame PC case? It might be the PSU's over power/current protection is kicking in, but I can't be sure. Have you used the PSU in the past? You said you followed the the mining setup PDF. Not sure where you are with that, so to review from that document: http://asrock.pc.cdn.bitgravity.com/Manual/BTC/H110%20Pro%20BTC+.pdf" rel="nofollow - http://asrock.pc.cdn.bitgravity.com/Manual/BTC/H110%20Pro%20BTC+.pdf You installed the first (single, one card) mining kit. So one video card in the board. You then started the board, installed the OS (Windows ??), and installed the board's basic drivers, and then the Nvidia/EVGA graphics driver. The PC boots and works fine in that configuration, checking the video card and driver in Device Manager. You then went through the sequence of installing the second video card, booting into Windows, verifying the video card is listed in Device Manager fine. You then continued this sequence for each of the video cards, until five were installed, correct? So at what point did the PC or PSU fail to start? Seems to be after adding the fifth video card, but that is not clear from your post. But you have seen the PC work with fewer than five video cards in it, correct? The LED on the network input blinking when the PC is not running but connected to a PSU is the PSU's standby power supply partially powering the board, including the networking chip. ------------- http://valid.x86.fr/48rujh" rel="nofollow"> 
|
EdS wrote:Posted By: EdS
Date Posted: 06 Nov 2017 at 10:19am
|
Thanks for the response! PSU is brand new evga 1300 g2 gold, plugged into mobo with the following, per the pdf.. 1 x 24 pin 1x 8 pin near CPU 2x molex 4 pin 1 x SATA power 1x fan plug PSU spins up just fine when tested with EVGA "tester" that jumps the 2 pins. Mobo is mounted in an open case, on stand off screws with red felt washer and correct screw.. screws and mobo is on clear plexiglass. |
Posted By: EdS
Date Posted: 06 Nov 2017 at 10:21am
|
There was no OS... it never got that far. The PSU just clicks.. the mobo will not do anything. No cpu fan.. nothing. No boot screen.. no chance to insert bootable thumbdrive with windows 10. |
Posted By: EdS
Date Posted: 06 Nov 2017 at 10:38am
|
" rel="nofollow - this diagram does not show the 8 pin near the cpu being plugged in? Thoughts? http://cryptomining-blog.com/wp-content/uploads/2017/07/asrock-h110-pro-btc-plus-motherboard-3.jpg |
Posted By: pro11
Date Posted: 12 Nov 2017 at 6:08am
|
I have the same problem. My Mining Rig was working just fine with MSI Z170A SLI Plus motherboard and 5 GPU's, but I wanted to have more GPU's , so I an AsRock H110 yesterday, mounted everything like in the PDF, but I couldn't boot it, nothing on the screen, not even the BIOS. My Screen is connected to the DVI port on the MoBo, but says "NO Signal". I booted this morning with a Windows 10 SSD, it started, then when I turned it off to change BIOS settings, but to no avail. I'm stripping it from everything, just to see if I can get to the BIOS, nothing. |
Posted By: EdS
Date Posted: 12 Nov 2017 at 7:45am
| I returned my asrock Mobo for and bought a gigabyte mining h110 board... and my rig was up and running within a few days. I want to use the Asrock.. but it doesn't seem like its a useble set up. |
Posted By: cy52
Date Posted: 22 Dec 2017 at 9:06am
| " rel="nofollow - Same here :( Was really looking forward to this and no power to anything... what's up with this? Tried 2 diff CPUs, 3 diff RAM, and 3 diff PSU. |
Posted By: bpay14
Date Posted: 30 Jan 2018 at 9:33am
|
i just encounter the same issue... it was running with my PSU when i installing win10, i had my GPU directly put on the motherboard pciex16 slot.. everything was good.. after all configuration, setup the mining rig, with 6 GPU all connected to riser.. it was still ok.. then i start to run the mining job... after 5mins.. all shutdown, and will never boot up again.. what happens??
 |