Z370 Taichi Temps
Printed From: ASRock.com
Category: Technical Support
Forum Name: Intel Motherboards
Forum Description: Question about ASRock Intel Motherboards
URL: https://forum.asrock.com/forum_posts.asp?TID=7673
Printed Date: 27 Dec 2024 at 1:40am
Software Version: Web Wiz Forums 12.04 - http://www.webwizforums.com
Topic: Z370 Taichi Temps
Posted By: Lenster
Subject: Z370 Taichi Temps
Date Posted: 15 Feb 2018 at 2:54am
|
" rel="nofollow - Recently replace my 3770K with Z370 Taichi and 8700K Bin L741D739. Ram is G-Skill 3200 running at rated speed. Cooler is Corsair H100IV2( reused from old install). The problem is temps. At idle, it is 39C with the pump at highspeed (3170RPM) Running OCCT takes it up to 95 and Realbench almost to 100. It will spike to 56C at the slightest uptick of useage. I have pulled the pump and the AS5 has evenly spread evenly across the entire top of the cpu so I know the seating was proper. The 3770K oc'd to 4.2 and ran in the 30s and never higher than the 60s. All bios settings on the Taichi are at default save Vccio (1.1) and Vccsa(1.15) to get the ram to run at rated speed. If I try changing to any overclock settings such as all cores at 4.5 and offest voltage at -60 it idles at 51C. The only thing I can think of is that my AS5 paste is a year old. Any suggestions? ------------- Len |
Replies:
Posted By: Lenster
Date Posted: 15 Feb 2018 at 3:23am
|
By the way I forgot the BIOS is 1.30 ------------- Len |
Posted By: wagass
Date Posted: 15 Feb 2018 at 2:41pm
|
" rel="nofollow - What program are you using to check temps? Which fan header are you using on the mobo? |
Posted By: Lenster
Date Posted: 15 Feb 2018 at 8:38pm
Pump is hooked up directly to Sata power cable. H100I V2 fans are connected to cpu and cpu aux connectors and I have 3 other fans connected to Aux 1,2 and 3. Pump is running at 3120rpm and the water temp does heat up. Temps were measured using Coretemp and HWInfo64. ------------- Len |
wagass wrote:Posted By: Lenster
Date Posted: 16 Feb 2018 at 4:18am
|
I removed the pump, reapplied thermal paste and rotated the pump 90 degrees. Seems to be better. Idling at 35C and OCCT peaks at 75C. All BIOS setting at default except for VCCIO and VCCSA. I will wait a couple of day before experimenting. ------------- Len |
Posted By: Dikonou
Date Posted: 17 Feb 2018 at 2:34am
|
" rel="nofollow - Multicore on or off? Cstates on or off? With air ( Noctua NH-D15S double fan NF-A15 chromax black ) I see 29-31 idle and 56 at cinebench15 with multicore on......when multicore off max temp is 51... no serious load so far........Bios 1.30 as well Delided as well Conductonaut..... What are your volts?
|
Posted By: Lenster
Date Posted: 17 Feb 2018 at 2:52am
Cinibench15 hits 99C Multicore Disabled Vcore as reported by HWInfo64 is 1.232V max C states enabled. C3, C6, C7 are auto. Package C state is disabled VCCIO is 1.1 and VCCSA is 1.15. All other BIOS settings at default. ------------- Len |
Posted By: Dikonou
Date Posted: 17 Feb 2018 at 3:14am
|
" rel="nofollow - To be more exact on Cinebench15 i only test CPU ....... but my volts reach up to 1.439 max value on per core VID and 1.344 at taichi vcore max value.....HWInfo64 VCCIO is 1.224 and VCCSA is 1.272 Cstates disabled multicore enabled on CPU-Z while benchmarking with cinebench 15 the core voltage never went above 1.216!! Now which one gives the right numbers?
|
Posted By: Lenster
Date Posted: 17 Feb 2018 at 4:08am
I set the pump speed to high (from 2070 to 3150 RPM and my temps dropped from 99 to 81 on Cinibench. Then I set multi core to enabled and cstates to disabled and my temps went to 93. I expected as much. One thing I have noticed is that the liquid temp in the cooler only goes up to 36.1C while the CPU is at 87+ This looks like bad contact, but I have pulled the pump three times and the TIM is spread evenly across the entire die. This is the same H100I V2 I used on my 3770K. ------------- Len |