G10 DEAD / BRICKED
Printed From: ASRock.com
Category: Media&User's Review
Forum Name: Networking Products
Forum Description: ASRock Networking Products
URL: https://forum.asrock.com/forum_posts.asp?TID=8139
Printed Date: 21 Nov 2024 at 7:04pm
Software Version: Web Wiz Forums 12.04 - http://www.webwizforums.com
Topic: G10 DEAD / BRICKED
Posted By: FireStorm
Subject: G10 DEAD / BRICKED
Date Posted: 21 Mar 2018 at 8:04am
|
" rel="nofollow - Hello I updated my newest ASRock from 2.09 to 2.18 (newest firmware). Now the router is DEAD. I updated via WLAN with my laptop. The router is JUST dead, NO LED LIGHTS, NO WIFI, NO ACCESS via LAN CABLE. It is just dead. Before it worked, I just wanted a firmware update. I tried a hard resest (30/30/30) by pressing the RESET Button, no help. Any help available?
|
Replies:
Posted By: rups
Date Posted: 25 Mar 2018 at 10:54pm
|
Hello, it seems your router is soft-bricked. I had the same issue when installing the latest DD-WRT firmware. No Leds -> the router stucks at boot. I fixed it by disassembling the router and connection an raspberry pi serial connection to the serial port on the motherboard. Then i was able to access the UBOOT bootloader. I managed to tftp a working DD-WRT image from an working router and reflashed the NAND flash chip. Then it started up again but i needed several days to find out. I hope i have helped.
|
Posted By: FireStorm
Date Posted: 26 Mar 2018 at 1:32am
|
Thx, at least I got an answer. Problem: I do not have the equipment and I am not really good at those things. Hmm so I can only send it for repair obviously.
|
Posted By: margaspeak
Date Posted: 28 Mar 2018 at 12:31pm
| Just send it to repair shop then or ask someone to come over and fix it for you. |
Posted By: FireStorm
Date Posted: 29 Mar 2018 at 2:28am
" rel="nofollow -
HOW???
|
margaspeak wrote:Posted By: FireStorm
Date Posted: 04 Apr 2018 at 4:26pm
| " rel="nofollow - ??? |
Posted By: slurpeemachine
Date Posted: 11 Apr 2018 at 12:14pm
" rel="nofollow -
Hi Rups, I'm in the exact same situation as you, can you please help me out with the files you used? I'd greatly appreciate it. Thank you!
|
Posted By: FireStorm
Date Posted: 15 Apr 2018 at 2:43am
| Support is very bad here :-( |
Posted By: iherbak77
Date Posted: 21 Apr 2018 at 9:32pm
|
" rel="nofollow - Hi! Could you provide me with guide on how you disassembled and connected to the pi? Thanks
|
Posted By: iherbak77
Date Posted: 21 Apr 2018 at 9:33pm
" rel="nofollow -
Could you provide info on dissassembly and connectiong the pi? Thanks
|
Posted By: holly123
Date Posted: 31 Oct 2018 at 12:37am
|
" rel="nofollow - Hi, could you provide a detailed information about how you did it? This is the issue I have right now: U-Boot 2012.07 [Standard IPQ806X.LN,r40331] (Jun 22 2015 - 19:44:46) smem ram ptable found: ver: 0 len: 5 DRAM: 491 MiB NAND: SF: Unsupported manufacturer 00 ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 128 MiB MMC: PCI0 Link Intialized PCI1 Link Intialized In: serial Out: serial Err: serial cdp: get part failed for 0:HLOS Net: MAC1 addr:0:3:7f:ba:db:1 athrs17_reg_init: complete athrs17_vlan_config ...done S17c init done MAC2 addr:0:3:7f:ba:db:2 eth0, eth1 Hit any key to stop autoboot: 0 MMC Device 0 not found MMC Device 0 not found setenv - set environment variables (IPQ) # |