Print Page | Close Window

x370 Taichi - 3 fans on one header via splitter?

Printed From: ASRock.com
Category: Technical Support
Forum Name: AMD Motherboards
Forum Description: Question about ASRock AMD motherboards
URL: https://forum.asrock.com/forum_posts.asp?TID=8768
Printed Date: 19 Jul 2025 at 6:56am
Software Version: Web Wiz Forums 12.04 - http://www.webwizforums.com


Topic: x370 Taichi - 3 fans on one header via splitter?
Posted By: TrevinLC1997
Subject: x370 Taichi - 3 fans on one header via splitter?
Date Posted: 24 May 2018 at 4:44pm
I have 7 fans and need to know if I can use a 3 way splitter on each chas_fan header. 

These are the fans I am using: https://www.newegg.com/Product/Product.aspx%3FItem=N82E16835181132&cm_re=rgb_fan-_-35-181-132-_-Product" rel="nofollow - Corsair LL120  https://www.newegg.com/Product/Product.aspx?Item=N82E16835181132&cm_re=rgb_fan-_-35-181-132-_-Product

The spec sheet says each fan has a power draw of 0.3A.

Will it work fine or is there a chance of damaging the board?  Also what is the maximum power a chassis header can output?



Replies:
Posted By: Erasmus_Tycho
Date Posted: 25 May 2018 at 6:38am
" rel="nofollow - If my understanding is correct, each header is capable of 1amp, So if you're running 3 at .3, you should be good. I know I've run 2 on a single header, never 3 though.

Anyone else care to confirm?  


-------------
ASRock x370 Taichi V4.4| Ryzen 1800x | 16GB x 2 DDR4 3200 (14cas) | GTX 1080 Ti K|NGP|N | WD NVMe Black 512GB | 2 x 500GB Samsung EVO 960 | Corsair HX1000 | EK Custom Loop (360mm rad + 280mm rad)


Posted By: TooQik
Date Posted: 25 May 2018 at 11:11am
As Erasmus_Tycho pointed out, each fan header can supply 1A of current, so as long as your total current draw of all three fans is 1A or lower then you will be fine.

I'm currently running six fans on my radiator using a three way splitter on both the CPU_OPT/W_PUMP and CHA_FAN1 headers. My current draw for each fan is 0.3A, the same as the draw of the fans you're using.

It's also worth noting that the two headers that allow water pump control will allow up to 1.5A of current each. So if you have three fans on a splitter that require more than 1A and up to 1.5A, use the CPU_OPT/W_PUMP and/or CHA_FAN3/W_PUMP headers.


Posted By: cx5
Date Posted: 28 May 2018 at 5:08pm
" rel="nofollow - Get this powered splitter https://item.taobao.com/item.htm?spm=a1z09.2.0.0.3d232e8dvtWBMX&id=548529008038&_u=sb8lko6ee6d 

-------------
x370taichi@3.50gen4
AX750 Optane900P SN770
3800x PosdonZro4 BarrowPWM-17w>420x140x28
XFX SWFT319 6900XT
MSI RX560 LP to get Fluid Motion BlueskyFRC 75hz



Print Page | Close Window

Forum Software by Web Wiz Forums® version 12.04 - http://www.webwizforums.com
Copyright ©2001-2021 Web Wiz Ltd. - https://www.webwiz.net