Reset/Reboot Problems on B150M PRO4S/D3

Author

Message

Topic Search

Topic Options

Xaltar

Moderator Group

Joined: 16 May 2015
Location: Europe
Status: Offline
Points: 25043

Post Options

Post Reply

Quote Xaltar

Report Post

Thanks(0)

Quote

Topic: Reset/Reboot Problems on B150M PRO4S/D3
Posted: 19 Dec 2015 at 7:22pm

Good to hear and thanks for posting your solution Thumbs Up

braint

Newbie

Joined: 18 Dec 2015
Status: Offline
Points: 5

Post Options

Post Reply

Quote braint

Report Post

Thanks(0)

Quote

Posted: 19 Dec 2015 at 7:17pm

Right, all sorted.

Feel a bit foolish, but as I was about to swap power supplies I had a feeling that I didn't do a clear CMOS after the BIOS update... Turns out I was right! after clearing the CMOS, the reset problem was gone!!! all working fine now. Again, interesting that there was no problem with a cold boot, but there was with a reset!

Anyway. Lesson learned. hopefully this will serve as a useful bit of info for anyone else that has similar reset issues in the future!

Thanks for the suggestions/thoughts wardog/Xaltar.

Cheers,

Brian

Xaltar

Moderator Group

Joined: 16 May 2015
Location: Europe
Status: Offline
Points: 25043

Post Options

Post Reply

Quote Xaltar

Report Post

Thanks(1)

Quote

Posted: 19 Dec 2015 at 3:28am

If it is suffering voltage droop then no, you would see the issues only once the unit is fully powered. As you said, cold boot causes a surge which could be resulting in sufficient power to initialize the system where on a reset the board is detecting inadequate voltage delivery and preventing it. I am not saying that it is definitely the problem, only that it could be.

wardog

Moderator Group

Joined: 15 Jul 2015
Status: Offline
Points: 6447

Post Options

Post Reply

Quote wardog

Report Post

Thanks(0)

Quote

Posted: 19 Dec 2015 at 1:45am

Good. You have different PSU to test with.

braint

Newbie

Joined: 18 Dec 2015
Status: Offline
Points: 5

Post Options

Post Reply

Quote braint

Report Post

Thanks(0)

Quote

Posted: 19 Dec 2015 at 12:21am

Power supply is a Antec AR352. It's about 4 years old. It has been relatively lightly used, and have not had any problem on the motherboard used with it in the past.

I will try an alternative supply (in another case), however, if it were a power supply issue, I would have expected it to cause more issues from a cold boot (bigger in-rush current), than a reset.

Cheers,

Brian

wardog

Moderator Group

Joined: 15 Jul 2015
Status: Offline
Points: 6447

Post Options

Post Reply

Quote wardog

Report Post

Thanks(1)

Quote

Posted: 18 Dec 2015 at 3:44pm

What specific model number is your Antec PSU, and how old is it?

Also, double check the wiring leading from your case to the MB's System Panel Header.

braint

Newbie

Joined: 18 Dec 2015
Status: Offline
Points: 5

Post Options

Post Reply

Quote braint

Report Post

Thanks(0)

Quote

Posted: 18 Dec 2015 at 8:23am

Hi There,

I'm having a problem with my new B150M PRO4S/D3, updated to the latest bios version (1.50).
The problem is, when I either reboot the PC (e.g. from windows), or if I hit the reset button. I'm left with a blank screen (on either DVI or HDMI output), and the machine appears to have hung (fans whirring, but no activity). If I power off and on the machine, everything works fine. I'm not happy with having to keep power cycling the machine every time I need to reset (e.g. driver updates), so wanted to see if this was a known issue that will be fixed with a BIOS update, or whether I need to return the motherboard under warranty.

Full system details:

Motherboard: B150M PRO4S/D3 (BIOS version 1.50)
CPU: Intel Core i5-6500
RAM: 16GB (2x8GB) CORSAIR VENGENCE LP CML16GX3M2A1600C10
Antec 350W power supply
USB Keyboard + Mouse

and that's it... I've taken the system back to bare-bones to rule out any other hardware causing issues.

Regards,

Brian

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Xaltar Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 25043	Post Options Post Reply Quote Xaltar Report Post Thanks(0) Quote Reply Topic: Reset/Reboot Problems on B150M PRO4S/D3 Posted: 19 Dec 2015 at 7:22pm
	Good to hear and thanks for posting your solution

braint Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 18 Dec 2015 Status: Offline Points: 5	Post Options Post Reply Quote braint Report Post Thanks(0) Quote Reply Posted: 19 Dec 2015 at 7:17pm
	Right, all sorted. Feel a bit foolish, but as I was about to swap power supplies I had a feeling that I didn't do a clear CMOS after the BIOS update... Turns out I was right! after clearing the CMOS, the reset problem was gone!!! all working fine now. Again, interesting that there was no problem with a cold boot, but there was with a reset! Anyway. Lesson learned. hopefully this will serve as a useful bit of info for anyone else that has similar reset issues in the future! Thanks for the suggestions/thoughts wardog/Xaltar. Cheers, Brian

Xaltar Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 25043	Post Options Post Reply Quote Xaltar Report Post Thanks(1) Quote Reply Posted: 19 Dec 2015 at 3:28am
	If it is suffering voltage droop then no, you would see the issues only once the unit is fully powered. As you said, cold boot causes a surge which could be resulting in sufficient power to initialize the system where on a reset the board is detecting inadequate voltage delivery and preventing it. I am not saying that it is definitely the problem, only that it could be.

wardog Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Joined: 15 Jul 2015 Status: Offline Points: 6447	Post Options Post Reply Quote wardog Report Post Thanks(0) Quote Reply Posted: 19 Dec 2015 at 1:45am
	Good. You have different PSU to test with.

braint Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 18 Dec 2015 Status: Offline Points: 5	Post Options Post Reply Quote braint Report Post Thanks(0) Quote Reply Posted: 19 Dec 2015 at 12:21am
	Power supply is a Antec AR352. It's about 4 years old. It has been relatively lightly used, and have not had any problem on the motherboard used with it in the past. I will try an alternative supply (in another case), however, if it were a power supply issue, I would have expected it to cause more issues from a cold boot (bigger in-rush current), than a reset. Cheers, Brian

wardog Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Joined: 15 Jul 2015 Status: Offline Points: 6447	Post Options Post Reply Quote wardog Report Post Thanks(1) Quote Reply Posted: 18 Dec 2015 at 3:44pm
	What specific model number is your Antec PSU, and how old is it? Also, double check the wiring leading from your case to the MB's System Panel Header.

braint Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 18 Dec 2015 Status: Offline Points: 5	Post Options Post Reply Quote braint Report Post Thanks(0) Quote Reply Posted: 18 Dec 2015 at 8:23am
	Hi There, I'm having a problem with my new B150M PRO4S/D3, updated to the latest bios version (1.50). The problem is, when I either reboot the PC (e.g. from windows), or if I hit the reset button. I'm left with a blank screen (on either DVI or HDMI output), and the machine appears to have hung (fans whirring, but no activity). If I power off and on the machine, everything works fine. I'm not happy with having to keep power cycling the machine every time I need to reset (e.g. driver updates), so wanted to see if this was a known issue that will be fixed with a BIOS update, or whether I need to return the motherboard under warranty. Full system details: Motherboard: B150M PRO4S/D3 (BIOS version 1.50) CPU: Intel Core i5-6500 RAM: 16GB (2x8GB) CORSAIR VENGENCE LP CML16GX3M2A1600C10 Antec 350W power supply USB Keyboard + Mouse and that's it... I've taken the system back to bare-bones to rule out any other hardware causing issues. Regards, Brian