Error code 0d

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   Its the psu i have a 600w pit 2 more 16gb sticks no post error 0d took the sticks out posted and booted just fine.

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Chrisv741 Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 11 Dec 2023 Location: Nevada Status: Offline Points: 15	Post Options Post Reply Quote Chrisv741 Report Post Thanks(0) Quote Reply Topic: Error code 0d Posted: 16 Dec 2023 at 11:18am
	Its the psu i have a 600w pit 2 more 16gb sticks no post error 0d took the sticks out posted and booted just fine.

Qbert Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 05 Jul 2023 Location: USA Status: Offline Points: 15	Post Options Post Reply Quote Qbert Report Post Thanks(0) Quote Reply Posted: 06 Jul 2023 at 1:59pm
	I had the same problem with a new build (error code 0d and no display output) until yesterday. Configuration: ASRock X570 PG Velocita AMD Ryzen 9 5900X ASRock Radeon RX 6500 XT PG TeamGroup T-Force Vulcan Z DDR4-3200 What did not work: I had the 2?32 GB RAM modules in slots A2 & B2, per instructions. I tried to boot with the factory-installed BIOS because of warnings not to upgrade working MoBos, but it did not work. I updated to the new beta version, 5.01, released one week prior, and reset the CMOS by removing the battery for at least 5 min (I put in a new battery) and holding down the CMOS reset and power buttons for 30 s. However, the boot process still ended at code 0d. I read multiple forums that recommended trying to boot with every possible combination of each RAM module in each slot. I removed the module from B2, but it still stalled at 0d. What did: I moved the RAM to slot A1 (only one module installed) and booted up, pressing F2 to enter UEFI setup. In the "OC Tweaker" section, I changed the "Load XMP Setting" from "Auto" to "XMP 2.0 Profile 1: DDR4-3200 16-18-18-38 1.35 V". The "DRAM Frequency" automatically changed to "DDR4-3200" and the "DRAM Voltage" to "1.350". I saved the settings and rebooted with the second module in slot B1 (I did not want to move the working one). Then I was able to install Linux Mint and utilize all 64 GB of RAM.

W.B.Loon Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 08 May 2021 Status: Offline Points: 50	Post Options Post Reply Quote W.B.Loon Report Post Thanks(0) Quote Reply Posted: 28 May 2021 at 8:52am
	Outside of case get the same A6, 0D error code. Pretty sure this is a DOA MB.

ThreeDee Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 24 Jul 2019 Location: Billings,MT Status: Offline Points: 2396	Post Options Post Reply Quote ThreeDee Report Post Thanks(0) Quote Reply Posted: 26 May 2021 at 2:32pm
	Test outside the case using a screw driver or similar to short the power pins to start up system .. or try shorting pins before you pull out of case and remove the front panel power/reset connectors.
	\|Ryzen 5 5900\|ASRock X570 Taichi-BIOS 4.60\|2x16GB HyperX Predator RGB 3200@3600 1:1 IF\|ASRock RX 6700XT\|2 x PCIe 4.0 M.2 Drives for OS & Games\|850 WTT Seasonic 80+ Titanium PSU\|Noctua NH-D15\|

RLGL Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 29 Jul 2018 Location: MN Status: Offline Points: 2025	Post Options Post Reply Quote RLGL Report Post Thanks(0) Quote Reply Posted: 25 May 2021 at 6:11am
	Try this GUIDE
	Asrock Z370 Gaming K6,Intel i7 8700K, Asrock x570 Taichi

W.B.Loon Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 08 May 2021 Status: Offline Points: 50	Post Options Post Reply Quote W.B.Loon Report Post Thanks(0) Quote Reply Posted: 25 May 2021 at 5:20am
	Update: Have removed all devices, RAM, video card, etc. Only connections are power and the Front connections (Pwr switch, reset etc.) The first error code is A6 (SATA issues but none are connected) then goes to 0d error and no further progress. CPU is Ryzen 5 5600x\|ASRock X570 Phantom Gaming X. Have not removed motherboard to test boot outside of case, but this sounds like a dead board to me.

ThreeDee Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 24 Jul 2019 Location: Billings,MT Status: Offline Points: 2396	Post Options Post Reply Quote ThreeDee Report Post Thanks(0) Quote Reply Posted: 22 May 2021 at 7:45pm
	What CPU? .. and have you tried reseating it? ..check for bent pins etc .. ..also, have you tried booting the motherboard outside of your case to rule out anything being shorted out inside the case .. ie, rogue stand off .. etc Edited by ThreeDee - 22 May 2021 at 7:47pm
	\|Ryzen 5 5900\|ASRock X570 Taichi-BIOS 4.60\|2x16GB HyperX Predator RGB 3200@3600 1:1 IF\|ASRock RX 6700XT\|2 x PCIe 4.0 M.2 Drives for OS & Games\|850 WTT Seasonic 80+ Titanium PSU\|Noctua NH-D15\|

W.B.Loon Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 08 May 2021 Status: Offline Points: 50	Post Options Post Reply Quote W.B.Loon Report Post Thanks(0) Quote Reply Posted: 21 May 2021 at 4:09am
	Trying to boot a new Asrock Gaming X x570 motherboard but I keep getting a 0d error code. My understanding is this code indicates a problem connecting USB, PCIe, video card, RAM devices. I have removed all PCIe connections including the M.2 SSDs, have disconnected all the USB headers, have removed the wireless mouse USB connector, have removed and reseated all the RAM (I have four 8GB Thermaltake sticks) and then reduced them to only the A2/B2 slots and then swapped sticks, have removed and reseated the video card and when that did not change things I replaced it with an older card I know is functional. Nothing has gotten the boot process past the 0d error code.