ASRock Q1900M no BIOS output

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

you are right. After I change with a non-ECC memory, the problem goes away. 
Thanks.

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
mwgong Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 23 Jul 2015 Status: Offline Points: 5	Post Options Post Reply Quote mwgong Report Post Thanks(0) Quote Reply Topic: ASRock Q1900M no BIOS output Posted: 24 Jul 2015 at 9:51pm
	you are right. After I change with a non-ECC memory, the problem goes away. Thanks.

odiebugs Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 07 Jul 2015 Status: Offline Points: 193	Post Options Post Reply Quote odiebugs Report Post Thanks(0) Quote Reply Posted: 24 Jul 2015 at 2:49am
	You can't use that memory, it's ECC. Also you should use two or four sticks as you'll run in dual channel. But if you only want one stick that's ok, just letting you know. Please try to get memory off this list. http://www.asrock.com/mb/Intel/Q1900M/?cat=Memory I don't know if you can buy from here but this good memory and low price. http://www.newegg.com/Product/Product.aspx?Item=N82E16820231421 Plus it only 23.00 US and 4g not 2g. Edited by odiebugs - 24 Jul 2015 at 2:59am
	asrocking

mwgong Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 23 Jul 2015 Status: Offline Points: 5	Post Options Post Reply Quote mwgong Report Post Thanks(0) Quote Reply Posted: 24 Jul 2015 at 12:02am
	Since I don't have DVI cable, I connected to monitor using VGA and HDMI. This is the memory I used: http://www.ncix.com/detail/kingston-system-specific-memory-ktm-sx313-2g-cd-37683-1374.htm

Xaltar Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Joined: 16 May 2015 Location: Europe Status: Online Points: 24653	Post Options Post Reply Quote Xaltar Report Post Thanks(0) Quote Reply Posted: 23 Jul 2015 at 10:54pm
	The problem is likely memory incompatibility, if possible try some different RAM. The Q1900M only supports DDR3 1333 RAM (you can use higher but it will not run at it's rated speeds). If the RAM is rated at a voltage higher than 1.5v you can have compatibility problems on these boards as they only support 1.35 and 1.5v RAM. While some 1.65v modules will work they will work at 1.5v and could prove unstable in some cases.

odiebugs Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 07 Jul 2015 Status: Offline Points: 193	Post Options Post Reply Quote odiebugs Report Post Thanks(0) Quote Reply Posted: 23 Jul 2015 at 10:21pm
	Which port are you using to monitor, have you tried DVI. Make sure the monitor setting is the same one you use on board, monitor must be set to DVI if it's plugged into DVI. Was the memory off the QVL, and have you tried only one stick to test the board ? Edited by odiebugs - 23 Jul 2015 at 10:22pm
	asrocking

mwgong Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 23 Jul 2015 Status: Offline Points: 5	Post Options Post Reply Quote mwgong Report Post Thanks(0) Quote Reply Posted: 23 Jul 2015 at 10:11pm
	I just installed a new ASRock Q1900M motheboard. When I power it on, the front panel light is on and the case fan runs, but there is no any output on monitor, like BIOS information. Any idea what might go wrong ?