Z77 Pro4M TPM

Author

Message

Topic Search

Topic Options

Xaltar

Moderator Group

Joined: 16 May 2015
Location: Europe
Status: Offline
Points: 25073

Post Options

Post Reply

Quote Xaltar

Report Post

Thanks(0)

Quote

Topic: Z77 Pro4M TPM
Posted: 01 Jun 2018 at 4:52pm

Awesome, looking forward to seeing what you find Thumbs Up

aksa0110

Newbie

Joined: 31 May 2018
Location: Serbia
Status: Offline
Points: 6

Post Options

Post Reply

Quote aksa0110

Report Post

Thanks(0)

Quote

Posted: 01 Jun 2018 at 3:20pm

Yes, my plan was to look and trace silicon on motherboard to see if it leads to somewhere or not. Otherwise there is no point in doing this.

I will dismantle my computer in the next couple of days and take a good look on the motherboard. After that I will post my findings and some pictures if I am successful.

Xaltar

Moderator Group

Joined: 16 May 2015
Location: Europe
Status: Offline
Points: 25073

Post Options

Post Reply

Quote Xaltar

Report Post

Thanks(0)

Quote

Posted: 01 Jun 2018 at 1:32am

It entirely depends on if the required silicon is present. If the traces are just leading nowhere then soldering pins to the header will achieve nothing. If you can find out what pins carry the data signals and test for to see if anything is coming through them, that's where I would start.

Odds are that some pins will be connected to something (power, ground etc) but if the data pins connect to nothing (absent controller chip) then you are wasting your time.

If you are not lucky with the pinouts then you could always try something like 3rd party encryption software. There are quite a few options out there.

aksa0110

Newbie

Joined: 31 May 2018
Location: Serbia
Status: Offline
Points: 6

Post Options

Post Reply

Quote aksa0110

Report Post

Thanks(0)

Quote

Posted: 31 May 2018 at 7:18pm

Hello guys,

This is my first post, one out of many I hope, and I am in need of your assistance.

I want to have TPM on my motherboard Z77 Pro4M which does not have TPM pins but on the motherboard there is TPM header but the pins/connector is not soldered onto motherboard. I am thinking of soldering some pins onto the motherboard where TPM header is supposed to be and after attach module to it.

My question is can this be done so that I can use TPM? If there is no factory soldered pins for TPM is there any software issues I should be aware of or any other issue that comes to your mind?

I have tried with local dealers to figure this one out but every one of them say that the motherboard is in End of life cycle and that they can not acquire original manufacturers parts.

What do you think, please share your thoughts with me whatever you think.

Thank you.

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Xaltar Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 25073	Post Options Post Reply Quote Xaltar Report Post Thanks(0) Quote Reply Topic: Z77 Pro4M TPM Posted: 01 Jun 2018 at 4:52pm
	Awesome, looking forward to seeing what you find


aksa0110 Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 31 May 2018 Location: Serbia Status: Offline Points: 6	Post Options Post Reply Quote aksa0110 Report Post Thanks(0) Quote Reply Posted: 01 Jun 2018 at 3:20pm
	Yes, my plan was to look and trace silicon on motherboard to see if it leads to somewhere or not. Otherwise there is no point in doing this. I will dismantle my computer in the next couple of days and take a good look on the motherboard. After that I will post my findings and some pictures if I am successful.

Xaltar Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 25073	Post Options Post Reply Quote Xaltar Report Post Thanks(0) Quote Reply Posted: 01 Jun 2018 at 1:32am
	It entirely depends on if the required silicon is present. If the traces are just leading nowhere then soldering pins to the header will achieve nothing. If you can find out what pins carry the data signals and test for to see if anything is coming through them, that's where I would start. Odds are that some pins will be connected to something (power, ground etc) but if the data pins connect to nothing (absent controller chip) then you are wasting your time. If you are not lucky with the pinouts then you could always try something like 3rd party encryption software. There are quite a few options out there.


aksa0110 Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 31 May 2018 Location: Serbia Status: Offline Points: 6	Post Options Post Reply Quote aksa0110 Report Post Thanks(0) Quote Reply Posted: 31 May 2018 at 7:18pm
	Hello guys, This is my first post, one out of many I hope, and I am in need of your assistance. I want to have TPM on my motherboard Z77 Pro4M which does not have TPM pins but on the motherboard there is TPM header but the pins/connector is not soldered onto motherboard. I am thinking of soldering some pins onto the motherboard where TPM header is supposed to be and after attach module to it. My question is can this be done so that I can use TPM? If there is no factory soldered pins for TPM is there any software issues I should be aware of or any other issue that comes to your mind? I have tried with local dealers to figure this one out but every one of them say that the motherboard is in End of life cycle and that they can not acquire original manufacturers parts. What do you think, please share your thoughts with me whatever you think. Thank you.