|
970 pro 3 R2.0 |
Post Reply 
|
| Author | |
kenny61 
Newbie 
Joined: 09 Mar 2016 Status: Offline Points: 6 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: 970 pro 3 R2.0Posted: 09 Mar 2016 at 4:00pm |
|
Hi event viewer in win 10 I am getting the following warning every 60 seconds
Component: AMD Northbridge Error Source: Corrected Machine Check Error Type: 28 Processor APIC ID: 0
when I check the details the process id is always svchost (localservicenonetwork)
I am running a AMD Fx 8150 on an asrock 970 pro3 r2.0 with no overclocking and just graphics card and stick of memory, clean install of win 10 and all drivers and bios up to date. Ran a stress test without any problems. Is this a cpu fault or a driver issue kenny
kenny |
|
 |
|
|
Xaltar
Moderator Group 
Joined: 16 May 2015 Location: Europe Status: Offline Points: 25028 |
Post Options
Thanks(0)
Quote Reply
Posted: 09 Mar 2016 at 4:40pm |
|
Check the temperatures on your motherboard heatsinks. By the sound of it the Northbridge is overheating. If it is getting very hot check the heatsink and make sure it has not come loose. If it is still attached properly and still overheating you may want to try another power supply as well as possibly add a fan to the system that blows on the Northbridge heatsink.
|
|
|
|
|
|
|
kenny61
Newbie
Joined: 09 Mar 2016 Status: Offline Points: 6 |
Post Options
Thanks(0)
Quote Reply
Posted: 09 Mar 2016 at 5:24pm |
|
Dont think its a heat issue i get about dozen listed in a row during win 10 start up then 1 every 60 seconds.
Tried different power supply but still does it. Also tried win 7 and its the same so rulesout win 10 Kenny |
|
|
|
|
Xaltar
Moderator Group
Joined: 16 May 2015 Location: Europe Status: Offline Points: 25028 |
Post Options
Thanks(0)
Quote Reply
Posted: 09 Mar 2016 at 5:30pm |
|
During startup the OS initializes drivers for the hardware components, many of which are controlled by the Northbridge so it would stand to reason that it would run hotter during this period. In most cases where I have seen this issue it has come down to either heat or bad power. On occasion it can be driver/software related but given you are having the same issue on both win 7 and win 10 I doubt that is the case.
It could be corrupted data in the UEFI and windows polling a particular device off the northbridge every 60 seconds so it may be worth while trying a CMOS clear, preferably via the battery removal method to be sure the RTC data is cleared too.
|
|
|
|
|
|
|
|
kenny61
Newbie
Joined: 09 Mar 2016 Status: Offline Points: 6 |
Post Options
Thanks(0)
Quote Reply
Posted: 09 Mar 2016 at 8:05pm |
|
Will check for heat and clear bios to see if that helps
Will keep this updated Kenny Edited by kenny61 - 09 Mar 2016 at 8:39pm |
|
|
|
|
kenny61
Newbie
Joined: 09 Mar 2016 Status: Offline Points: 6 |
Post Options
Thanks(0)
Quote Reply
Posted: 10 Mar 2016 at 12:56am |
|
Well its not the northbridge overheating as I had cold air blowing on it during start up, cleared the bios by removing battery. Interesting to note that the amount warnings created at start up = the amount of svchost that are running when windows boot. so i'm left with either cpu has fault or motherboard has fault/cant handle cpu kenny
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options