ASRock.com Homepage
Forum Home Forum Home > Technical Support > AMD Motherboards
  New Posts New Posts RSS Feed - A520M Gaming - not booting to bios
  FAQ FAQ  Forum Search Search  Events   Register Register  Login Login

A520M Gaming - not booting to bios
 Post Reply Post Reply Page  <12
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Xaltar View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 16 May 2015
Location: Europe
Status: Offline
Points: 24893 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Xaltar Quote  Post ReplyReply Direct Link To This Post Posted: 15 Dec 2024 at 5:59am
In that case the RAM is the likely culprit. P3.4 should support the 5500 so that can't
be the problem.
Back to Top
pads View Drop Down
Newbie
Newbie
Avatar

Joined: 12 Dec 2024
Location: Leeds uk
Status: Offline
Points: 185 		Post Options Post Options   Thanks (0) Thanks(0)   Quote pads Quote  Post ReplyReply Direct Link To This Post Posted: 15 Dec 2024 at 6:21am
That's what I thought so I swapped the RAM for the 'Corsair Vengeance LPX 32GB (2x16GB) 3200MT/s DDR4' which are working in the other pc. I still get 3 bleeps.
Peter
Back to Top
Xaltar View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 16 May 2015
Location: Europe
Status: Offline
Points: 24893 		Post Options Post Options   Thanks (1) Thanks(1)   Quote Xaltar Quote  Post ReplyReply Direct Link To This Post Posted: 15 Dec 2024 at 7:23am
Hmm, could be a DOA CPU, the board is less likely to be the culprit given it is
giving you a beep code. Memory controllers are much more touchy these days than
they used to be and are a common failure point on modern CPUs (they are built into
the CPU these days). A dead IMC could give you 3 beeps (integrated memory controller).

Check the CPU for any bent over pins or darkening on the substrate. If
possible, try with the CPU from your other build to rule out anything else.
If the other CPU works then return the 5500.

This kind of issue can be a real pain to get to the bottom of....

Good luck :Y:
Back to Top
pads View Drop Down
Newbie
Newbie
Avatar

Joined: 12 Dec 2024
Location: Leeds uk
Status: Offline
Points: 185 		Post Options Post Options   Thanks (0) Thanks(0)   Quote pads Quote  Post ReplyReply Direct Link To This Post Posted: 15 Dec 2024 at 8:06pm
I tried swapping the CPU and am wondering if I was giving false information.

There is still no display but the three bleeps now rapid sort of bleep-bleep-bleep.
Previously it was bleeeep ----- bleeeep ---- bleeeep, long beeps and not as rapid.
If you understand my meaning.

I didn't appreciate there was adifference until now.
Peter
Back to Top
pads View Drop Down
Newbie
Newbie
Avatar

Joined: 12 Dec 2024
Location: Leeds uk
Status: Offline
Points: 185 		Post Options Post Options   Thanks (0) Thanks(0)   Quote pads Quote  Post ReplyReply Direct Link To This Post Posted: 15 Dec 2024 at 9:50pm

So I decided I needed to put things back together (I need other pc to go to grandchild -christmas). All except power supply still on borrowed one.

Low and behold - no bleeps, and a 'BIOS' screen displayed. Not the full BIOS but a screen stating 'New PC installed' and asking 'Press Y to reset fTPM' or 'Press N to keep previous fTPM'.

I presume I need to press 'Y' to restore fTPM.

I'll await your reply before I do anything else.
Thank you
Peter
Back to Top
Xaltar View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 16 May 2015
Location: Europe
Status: Offline
Points: 24893 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Xaltar Quote  Post ReplyReply Direct Link To This Post Posted: 15 Dec 2024 at 11:57pm
https://www.reddit.com/r/Windows10/comments/q62k5h/new_cpu_installed_should_i_reset_ftpm_or_press_no/

Given it's a new system you should be fine pressing "Y"

The joys of system building, I once tore my hair out for 3 days on a client build
that wouldn't POST, eventually I gave up and started to tear the whole thing
down ready to send it all back to my supplier for RMA, just as I was about to
pull the board and CPU I decided to give it one more go, lo and behold it POSTed....
To this day I still don't know what the issue was
Back to Top
pads View Drop Down
Newbie
Newbie
Avatar

Joined: 12 Dec 2024
Location: Leeds uk
Status: Offline
Points: 185 		Post Options Post Options   Thanks (0) Thanks(0)   Quote pads Quote  Post ReplyReply Direct Link To This Post Posted: Yesterday at 12:13am
Many thanks - I pressed Y and I now have the the normal BIOS screen.

The next thing I dare do is swap back the PSU.
Fingers crossed - here goes.
Peter
Back to Top
pads View Drop Down
Newbie
Newbie
Avatar

Joined: 12 Dec 2024
Location: Leeds uk
Status: Offline
Points: 185 		Post Options Post Options   Thanks (0) Thanks(0)   Quote pads Quote  Post ReplyReply Direct Link To This Post Posted: Yesterday at 12:21am
Success.

As you say - "To this day I still don't know what the issue was"

Many thanks for all of your advice.
Peter
(ps - I still have to connect the hard drives etc but they should be ok - I hope!
Peter
Back to Top
Xaltar View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 16 May 2015
Location: Europe
Status: Offline
Points: 24893 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Xaltar Quote  Post ReplyReply Direct Link To This Post Posted: 22 hours 5 minutes ago at 7:43am
Fantastic, glad it worked out for you. I am sure your grandkids are going to have
an amazing Christmas!
Back to Top
pads View Drop Down
Newbie
Newbie
Avatar

Joined: 12 Dec 2024
Location: Leeds uk
Status: Offline
Points: 185 		Post Options Post Options   Thanks (0) Thanks(0)   Quote pads Quote  Post ReplyReply Direct Link To This Post Posted: 21 hours 48 minutes ago at 8:00am
Many thanks for your guidance
Peter
Back to Top
 Post Reply Post Reply Page  <12
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 0.156 seconds.