ASRock.com Homepage
Forum Home Forum Home > Technical Support > Intel Motherboards
  New Posts New Posts RSS Feed - x99 extreme 11 PCI Express Problems
  FAQ FAQ  Forum Search Search  Events   Register Register  Login Login

x99 extreme 11 PCI Express Problems
 Post Reply Post Reply Page  12>
Author
Message Reverse Sort Order
  Topic Search Topic Search  Topic Options Topic Options
phrenesis View Drop Down
Newbie
Newbie


Joined: 28 Jan 2017
Status: Offline
Points: 8 		Post Options Post Options   Thanks (0) Thanks(0)   Quote phrenesis Quote  Post ReplyReply Direct Link To This Post Topic: x99 extreme 11 PCI Express Problems
    Posted: 28 Jan 2017 at 7:33pm
Hello Wardog and others

I attached the 4pin molex connector, it did not make any difference.

I clean installed win10 again, updated all the chipset drivers. The BSOD when updating the GPU driver went away.

It still does give me 92/94/96 Error Code on Dr. Debug sometimes.
The WHEA correctable Error when starting is still there.

I ran prime95 for an hour or two as well, no error, max temp 63° with 100% CPU load (no OC obviously)

EDIT: I found out it might have been a driver problem by debugging the dump and checking google, some others even with different chipsets had the same error message when chipset drivers were bugged or not the newest installed.


Edited by phrenesis - 28 Jan 2017 at 8:00pm
Back to Top
wardog View Drop Down
Moderator Group
Moderator Group


Joined: 15 Jul 2015
Status: Offline
Points: 6447 		Post Options Post Options   Thanks (0) Thanks(0)   Quote wardog Quote  Post ReplyReply Direct Link To This Post Posted: 28 Jan 2017 at 10:23am
Originally posted by phrenesis phrenesis wrote:

Man, I think I was blind. Found them, will test tomorrow. Thanks a lot wardog!


hehehe, Post back when you get to it.
Back to Top
phrenesis View Drop Down
Newbie
Newbie


Joined: 28 Jan 2017
Status: Offline
Points: 8 		Post Options Post Options   Thanks (0) Thanks(0)   Quote phrenesis Quote  Post ReplyReply Direct Link To This Post Posted: 28 Jan 2017 at 10:14am
Man, I think I was blind. Found them, will test tomorrow. Thanks a lot wardog!
Back to Top
phrenesis View Drop Down
Newbie
Newbie


Joined: 28 Jan 2017
Status: Offline
Points: 8 		Post Options Post Options   Thanks (0) Thanks(0)   Quote phrenesis Quote  Post ReplyReply Direct Link To This Post Posted: 28 Jan 2017 at 10:10am
I checked my psu, it does not have a 4pin molex connector.....
Back to Top
wardog View Drop Down
Moderator Group
Moderator Group


Joined: 15 Jul 2015
Status: Offline
Points: 6447 		Post Options Post Options   Thanks (0) Thanks(0)   Quote wardog Quote  Post ReplyReply Direct Link To This Post Posted: 28 Jan 2017 at 10:10am
Originally posted by phrenesis phrenesis wrote:

my PSU doesn't have any 4pin molex.


The Corsair website for the RMx 750 shows you should have 7 4-pin Molex connectors on, well, one or two modular cables.

http://www.corsair.com/en-us/rmx-series-rm750x-750-watt-80-plus-gold-certified-fully-modular-psu
Back to Top
wardog View Drop Down
Moderator Group
Moderator Group


Joined: 15 Jul 2015
Status: Offline
Points: 6447 		Post Options Post Options   Thanks (0) Thanks(0)   Quote wardog Quote  Post ReplyReply Direct Link To This Post Posted: 28 Jan 2017 at 10:06am
Originally posted by phrenesis phrenesis wrote:

This 4pin? http://imgur.com/a/kB9D3 I thought this one is only if you have more than 3 GPUS installed


Yea. Excuse me, I overlooked this MB has two PCIE_PWR connectors.

Use the one you pictured in that imgur link. PCIE_PWR1



Nothing harmful will come of it if the bus doesn't need it bucked up some with connecting this.
Back to Top
phrenesis View Drop Down
Newbie
Newbie


Joined: 28 Jan 2017
Status: Offline
Points: 8 		Post Options Post Options   Thanks (0) Thanks(0)   Quote phrenesis Quote  Post ReplyReply Direct Link To This Post Posted: 28 Jan 2017 at 9:36am
All the parts arrived today, and is a fresh install

PSU : Corsair RMx 750W

I installed the RAM as shown in the manual (A_1, B_1, C_1, D_1) 

I tried PCI Express slot 1,2,4,5 with the gpu

I know the Dr. Debug code from the manual.


Edit: Tested with single stick as well

This 4pin? http://imgur.com/a/kB9D3 I thought this one is only if you have more than 3 GPUS installed

It also has PCIE_PWR2, my PSU doesn't have any 4pin molex.


Edited by phrenesis - 28 Jan 2017 at 10:02am
Back to Top
wardog View Drop Down
Moderator Group
Moderator Group


Joined: 15 Jul 2015
Status: Offline
Points: 6447 		Post Options Post Options   Thanks (0) Thanks(0)   Quote wardog Quote  Post ReplyReply Direct Link To This Post Posted: 28 Jan 2017 at 9:17am
Meh, this is another ?

PSU. What Model Corsair, and how old is it?

I ask because a lot of folks seemingly hold on to their PSU's well after their Use By date. From build to build.
Back to Top
wardog View Drop Down
Moderator Group
Moderator Group


Joined: 15 Jul 2015
Status: Offline
Points: 6447 		Post Options Post Options   Thanks (0) Thanks(0)   Quote wardog Quote  Post ReplyReply Direct Link To This Post Posted: 28 Jan 2017 at 9:04am
And seeings I forgot in my first reply ............

FYI:
http://www.asrock.com/support/faq.asp?id=334
Back to Top
wardog View Drop Down
Moderator Group
Moderator Group


Joined: 15 Jul 2015
Status: Offline
Points: 6447 		Post Options Post Options   Thanks (0) Thanks(0)   Quote wardog Quote  Post ReplyReply Direct Link To This Post Posted: 28 Jan 2017 at 9:02am
Well, you're not running out of lanes, that's for sure. Not with that i7-6850K


At the bottom left of the MB is a downward facing 4-pin Molex connector. Plug/power it from a separate cable coming directly from the PSU. It provides additional/supplemental power to the PCIe bus if and or when needed.


Too, your 4 sticks? A single kit?


And JiC, proper mem slots to use:
Back to Top
 Post Reply Post Reply Page  12>
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 0.095 seconds.