X399 Taichi Dr. Debug Error |
Post Reply |
Author | |
scjconsulting
Newbie Joined: 04 Apr 2017 Location: Minnesota Status: Offline Points: 57 |
Post Options
Thanks(0)
Posted: 12 Mar 2019 at 4:19am |
I am building a X399 Taichi Threadripper 2950x system. After putting it almost all together, the Dr. Debug shows 00, which the book says to reinstall the CPU and then reset the CMOS. Before doing all that yet, I would like to know what went wrong. I have installed CPUs before and while the 2950x is pretty big, I can't think of a way the CPU was installed incorrectly as it only goes in and gets tightened down one way. Thanks. |
|
scjconsulting
|
|
xhue
Groupie Joined: 17 Aug 2018 Status: Offline Points: 634 |
Post Options
Thanks(1)
|
Threadrippers are known for having tough time getting them well-seated the first time.
There is more - certain mobos had bad/faulty Foxconn TR4 sockets. The two things above can easily break contact between some socket pins and the CPU itself. Actually, even 1 badly contacting pin can flip you in your face. With more than 4000 pins you pull the odds. My suggestion is to re-install the CPU, check all RAM, cabling and other connectors, clear CMOS and give it another try. |
|
scjconsulting
Newbie Joined: 04 Apr 2017 Location: Minnesota Status: Offline Points: 57 |
Post Options
Thanks(0)
|
Thanks for your reply. It will take a few days to get some more silver compound, but will get back to you. |
|
scjconsulting
|
|
scjconsulting
Newbie Joined: 04 Apr 2017 Location: Minnesota Status: Offline Points: 57 |
Post Options
Thanks(0)
|
I reinstalled the CPU and I guess I am making progress? After going through the codes, I get a d6 and the an 0d and then stops. Sometime it goes through the codes twice. The d6 means graphics card problem. It is a MSI 2070 which you remember is in the 2nd PCIE slot because the cooler blocks the first slot. Should I buy a new cooler, one where the fans exhaust on the top (240 or 280mm), and then then the graphics card could be in the 1st PCIE slot? I was thinking a Corsair H115i. Are there any you recommend? I'm still a little confused on the Clean CMOS switch. Do you push the button with the power on/off or plugged in/not? Thanks. |
|
scjconsulting
|
|
xhue
Groupie Joined: 17 Aug 2018 Status: Offline Points: 634 |
Post Options
Thanks(0)
|
Hmm, let's see.
To clear CMOS you need to unplug the power cord of your PC from the wall. Then push the Clear CMOS switch and hold it for 10-15 seconds. Alternatively, you can achieve the same by the on-board jumper. The fact that you are seeing progress when moving the CPU is telling. What do you say you try it once more? Let's try this, in the following order: - clear CMOS as described above; - try booting again; observe the behavior; - update BIOS via your mobo flashback option; - clear CMOS again, try booting; - remove the GPU, clear CMOS and try booting again; - re-seat your RAM sticks, I know it sounds crazy but it isn't; If none of the above helps then maybe you need to return the mobo. As for the coolers - h115i is very good cooler but it doesn't have TR4 coldplate. I'd recommend the Enermax Liqtech TR4 II 280mm or 360mm variants. Look for the 2nd gen moniker, as the 1st gen had issues with the cooling liquid. |
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |