ASRock.com Homepage
Forum Home Forum Home > Technical Support > AMD Motherboards
  New Posts New Posts RSS Feed - A couple of problems with Asrock X570 Taichi
  FAQ FAQ  Forum Search Search  Events   Register Register  Login Login

A couple of problems with Asrock X570 Taichi

 Post Reply Post Reply Page  123 7>
Author
Message
shmerl View Drop Down
Groupie
Groupie


Joined: 23 Oct 2017
Status: Offline
Points: 612
Post Options Post Options   Thanks (0) Thanks(0)   Quote shmerl Quote  Post ReplyReply Direct Link To This Post Topic: A couple of problems with Asrock X570 Taichi
    Posted: 03 Sep 2019 at 2:42am
I just finished my build (Asrock X570 Taichi / Ryzen 9 3900X), and I noticed a few issues:

1. After waking up from suspend, the motherboard debug indicator LEDs and on-board LEDs on the power/reset buttons don't turn off and continue glowing.

The debug indicator shows 00 (and stays that way during normal system operation).

2. The SB chipset always runs at around 60C or so, no matter what fan setting is enabled. That's a bit strange. I'm also using an NVMe SSD in the top slot.

That happens even with latest firmware/bios 2.0
Back to Top
Xaltar View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 16 May 2015
Location: Europe
Status: Offline
Points: 24653
Post Options Post Options   Thanks (0) Thanks(0)   Quote Xaltar Quote  Post ReplyReply Direct Link To This Post Posted: 03 Sep 2019 at 3:39am
That is odd, I will check it out on my X570 Taichi as soon as I have some free
time, probably Wednesday. I don't have these issues with 1.80 on my board
however. When my system enters sleep it reboots to wake, not exactly normal but
then again, I have not done a fresh OS install on it yet so I need to take care
of that first. If you have not performed a clean install on this system (used
the OS drive from a different system) then that would be a solid first step.

Sleep was problematic with both first and second gen Ryzen for quite a while
after they launched. I suspect the issues are 2 fold, the AGESA and the OS. I
had endless issues with sleep on my X370 Taichi and 1600x, I tried countless
BIOS versions and in the end, the issue just disappeared, seemingly on it's
own. Checking my logs I discovered Windows had updated itself while I was out
and that was what eventually fixed it.

As for the chipset temps, good exhaust airflow is essential with these X570
boards, you want to pump the heat out of the case as quickly as possible. I
typically run my systems with positive pressure (more intake than exhaust) and
noticed my temps were pretty high. Balancing the pressure a bit better dropped
my chipset temp by about 5c. If 60c is a load temp however, that is pretty
decent for an X570 it seems. I have seen reports of temps up to the low 80s
under load and apparently, up to 85c is within "safe" operating temperature.
Still no official word on max operating temps for the chipset but I would aim
for sub 80c, a spike or 2 over that in an hour long stress test is fine but the
average should be under 80c, if for no other reason than to limit heat
saturation of surrounding components as well as dumping hot air into your case.

Edited by Xaltar - 03 Sep 2019 at 3:40am
Back to Top
shmerl View Drop Down
Groupie
Groupie


Joined: 23 Oct 2017
Status: Offline
Points: 612
Post Options Post Options   Thanks (0) Thanks(0)   Quote shmerl Quote  Post ReplyReply Direct Link To This Post Posted: 03 Sep 2019 at 5:08am
I'm using Linux (freshly installed on this system on NVMe), but it would be strange if suspend issues would be OS specific. Also, suspend works fine for me on X370 Taichi/Ryzen 2700X (also using Linux). This LED / resume is unique to X570.

Also, I noticed this in older firmware dmesg used to give this error:

ACPI: [Firmware Bug]: BIOS _OSI(Linux) query


Which indicated that Asrock didn't handle Linux reporting to firmware OS name for ACPI purposes. In 2.0 this error is gone, so I assume that's good!

(Some details on related issues here: https://wiki.archlinux.org/index.php/DSDT ).

I can report this LED annoyance to Asrock directly, unless they can see this thread on the forum.


Regarding positive pressure - interesting point. I also run my case with positive pressure, to keep dust out, since I'm using good quality dust filters from Demciflex. I get, how it can affect thermals negatively.

Nvme runs at around 45C on idle, while in my older case whith X370 Taichi it was around 32+C. Not sure when it starts throttling (Samsuing 970 Evo Plus). It reaches 60C with heavy I/O. If it's OK for chipset to run at 60C may be I shouldn't worry. I tried loading the NVMe and GPU, the temperature didn't really rise for the chipset.

But may be lm-sensors aren't reporting it correctly? Though when inside the UEFI UI, it also shows it around 60+C, so I assume it's correct (for me the sensor is called SMBUSMASTER 1.
Back to Top
shmerl View Drop Down
Groupie
Groupie


Joined: 23 Oct 2017
Status: Offline
Points: 612
Post Options Post Options   Thanks (0) Thanks(0)   Quote shmerl Quote  Post ReplyReply Direct Link To This Post Posted: 03 Sep 2019 at 6:38am
I figured an interesting thing. In my case GPU was affecting the setup. I have Sapphire Pulse RX 5700XT, and basiclly by default, it has very passive fans policy on low load. GPU temps are quite high, and that's what's negatively affecting the heatsink and everything under it (nvme and the chipset).

I just tried radeon-profile: https://github.com/marazmista/radeon-profile and set more active fan curve. GPU temps dropped down, as as well as chipset went from 60C to 56C! Nvme went from 45C to 41C! So now I know what needs adjustment.
Back to Top
shmerl View Drop Down
Groupie
Groupie


Joined: 23 Oct 2017
Status: Offline
Points: 612
Post Options Post Options   Thanks (0) Thanks(0)   Quote shmerl Quote  Post ReplyReply Direct Link To This Post Posted: 03 Sep 2019 at 6:49am
Also, too bad Asrock made only first PCIe slot connected directly to the CPU. Putting the GPU there positions it right above NVMe and the chipset :( Not a very good thermal design. I suppose putting the GPU in the second PCIe slot would make ventilation above the chipset better.
Back to Top
shmerl View Drop Down
Groupie
Groupie


Joined: 23 Oct 2017
Status: Offline
Points: 612
Post Options Post Options   Thanks (0) Thanks(0)   Quote shmerl Quote  Post ReplyReply Direct Link To This Post Posted: 03 Sep 2019 at 8:11am
I wonder if putting some insulating material between the long edge of the GPU and the heatsink could improve things further.
Back to Top
kschendel View Drop Down
Newbie
Newbie


Joined: 21 Aug 2018
Status: Offline
Points: 86
Post Options Post Options   Thanks (0) Thanks(0)   Quote kschendel Quote  Post ReplyReply Direct Link To This Post Posted: 03 Sep 2019 at 10:35am
GPU's generally aren't PCIe bandwidth limited, so you probably wouldn't lose any real performance by putting it into the next slot. Might be worth experimenting with -- if you do, please report back!
Back to Top
shmerl View Drop Down
Groupie
Groupie


Joined: 23 Oct 2017
Status: Offline
Points: 612
Post Options Post Options   Thanks (0) Thanks(0)   Quote shmerl Quote  Post ReplyReply Direct Link To This Post Posted: 03 Sep 2019 at 11:14am
Yeah, good point, I'll give it a test. How much bandwidth does a GPU like RX 5700XT saturate? I guess it depends on the screen resolution too? Given that both board and card are PICe 4, I suppose even x8 bandwidth will be like x16 of PCIe 3?
Back to Top
shmerl View Drop Down
Groupie
Groupie


Joined: 23 Oct 2017
Status: Offline
Points: 612
Post Options Post Options   Thanks (0) Thanks(0)   Quote shmerl Quote  Post ReplyReply Direct Link To This Post Posted: 03 Sep 2019 at 11:21am
Also, are there any materials that are non conductive and are not prone for static electricity, while also having low thermal conductivity (thermal insulators)? Placing something like that between the GPU and the heatsink should help a bit I think. But styrofoam probably is a bad option, due to static electricity.
Back to Top
Xaltar View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 16 May 2015
Location: Europe
Status: Offline
Points: 24653
Post Options Post Options   Thanks (0) Thanks(0)   Quote Xaltar Quote  Post ReplyReply Direct Link To This Post Posted: 04 Sep 2019 at 12:28am
I would just drop the GPU into a lower slot. PCIe 4.0 x8 is more or less the same
as PCIe 3.0 x16, you are correct. The 2080ti doesn't saturate PCIe 3.0 x8 let
alone x16 so you should be fine with the 5700xt at PCIe 4.0 x8. If you are a
curious sort like myself, you can have a bit of fun benchmarking the GPU in each
slot to check for differences yourself. I strongly suspect you won't see more
than a margin of error difference even with the x4 slot
Back to Top
 Post Reply Post Reply Page  123 7>
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 0.281 seconds.