Asrock x370 no post no beep |
Post Reply | Page 12> |
Author | |
Xaltar
Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 24713 |
Post Options
Thanks(0)
Posted: 25 Sep 2019 at 7:02am |
This is incorrect, the standard voltage for DDR4 is 1.2v. 1.35v is common with XMP profiles but this is technically overvolting to facilitate the XMP overclock. At 1.2v all standard DDR4 RAM should POST, the highest rated, non XMP frequency for DDR4 is 2666 which does not require more than 1.2v. My 2800 kit uses 1.2v even with XMP enabled but my 3600 kit requires 1.35v for it's XMP to function. XMP will set the voltage automatically however. |
|
|
|
Xaltar
Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 24713 |
Post Options
Thanks(0)
|
I just looked up your RAM, it appears to be ECC RAM. While Unbuffered ECC RAM is
technically supported on Ryzen it may not be with your board. I suspect this has been your issue all along. Sorry, I should have checked your RAM first, it would have saved you some time. Return that ECC RAM and get some normal RAM from a reputable brand that is supported on your board. |
|
|
|
onesevennine
Newbie Joined: 21 Sep 2019 Status: Offline Points: 13 |
Post Options
Thanks(0)
|
I saw the reviews so I switched to a thermaltake smart 700w psu. But it's still not posting even after doing a cmos reset by using the jumper and removing the cmos battery
|
|
Xaltar
Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 24713 |
Post Options
Thanks(0)
|
The first thing I would do is get a decent Power Supply. Looking up that Kentek
unit all I see are bad reviews and reports of them dying. I suspect your unit may also be a very old model (new old stock maybe?). |
|
|
|
onesevennine
Newbie Joined: 21 Sep 2019 Status: Offline Points: 13 |
Post Options
Thanks(0)
|
Also just to note there is no post and no bios so I have no way to change the settings
|
|
onesevennine
Newbie Joined: 21 Sep 2019 Status: Offline Points: 13 |
Post Options
Thanks(0)
|
I reseated all the connections, reset the bios and removed the extra ram but it's still restarting after 10 seconds.
|
|
jdillipl
Newbie Joined: 03 Aug 2017 Location: USA Status: Offline Points: 159 |
Post Options
Thanks(0)
|
I have this motherboard. Yes there is a setting to control the speaker, but only to give a single beep for a successful POST. To the OP, use a bright light and magnifiers to verify that all connections are correct. Remove all drives, and all sticks of RAM except for one, in slot A2. Per the instructions, reset the BIOS / UEFI one more time. Now try powering up again.
Jake |
|
Asrock X370 Killer SLI/ac, Amd Ryzen 7 1700, GSkill FlareX F4-2400C16D-32GFX, RaidMax Thunder V2 735W PS
|
|
RLGL
Senior Member Joined: 29 Jul 2018 Location: MN Status: Offline Points: 2025 |
Post Options
Thanks(0)
|
Is there anything in the bios settings to turn it on?
|
|
Asrock Z370 Gaming K6,Intel i7 8700K,
Asrock x570 Taichi |
|
onesevennine
Newbie Joined: 21 Sep 2019 Status: Offline Points: 13 |
Post Options
Thanks(0)
|
Yes but it's not making any beeps.
|
|
RLGL
Senior Member Joined: 29 Jul 2018 Location: MN Status: Offline Points: 2025 |
Post Options
Thanks(0)
|
Do you have a speaker attached to the board?
|
|
Asrock Z370 Gaming K6,Intel i7 8700K,
Asrock x570 Taichi |
|
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |