ASRock.com Homepage
Forum Home Forum Home > Technical Support > AMD Motherboards
  New Posts New Posts RSS Feed - Can't get a B550M Pro 4 to POST
  FAQ FAQ  Forum Search Search  Events   Register Register  Login Login

Can't get a B550M Pro 4 to POST

 Post Reply Post Reply
Author
Message
jefarr View Drop Down
Newbie
Newbie


Joined: 12 Sep 2020
Status: Offline
Points: 5
Post Options Post Options   Thanks (0) Thanks(0)   Quote jefarr Quote  Post ReplyReply Direct Link To This Post Topic: Can't get a B550M Pro 4 to POST
    Posted: 12 Sep 2020 at 3:58am
I haven't built a PC in about a decade now, but at this point I've read through everything I can think of and run through enough familiar troubleshooting that I think it's time to ask for some help. Specs listed below.

Currently running with a single 16g stick of ram in slot A2. RAM has been reseated, 24pin power and 8 pin CPU power have been reseated.

I'm using a DarkFlash DLM22 which doesn't have a speaker, so for the moment I don't know if I get a POST beep.

It will power up and the RGB on the AIO starts its animation (connected directly to the ARGB header on the motherboard, no controller), the USB keyboard will (eventually) light up and numlock/caps lock will turn on/off when I press them (at least according to the indicator lights).

The Post Status Checker lights will briefly light up for CPU and DRAM, then turn off and BOOT and VGA lights will flash, then stay on for some seconds, while the Display Port output 1 on the graphics card wakes up and I get a blinking cursor in the upper left of the screen which blinks about a half dozen times before the signal drops out, and then the BOOT and VGA PSC lights turn off... and then nothing.

Pressing F2 or DEL to try and enter UEFI has no discernible effect.

If I clear CMOS, the PSC lights for CPU and DRAM will stay lit for longer on the next startup, and the lights on my keyboard (a basic Dell USB board from over 10 years ago) will take longer to "wake up". After that it's all the same as above.

QVL from AsRock.. my rams are CAS14 where all the official listed from G.Skill are CAS16... pcpartpicker lists this RAM as compatible tho, for whatever that's worth.


Specs:

EVGA Supernova 550

AsRock B550m Pro4

Ryzen 3900X

CoolerMaster ML240 RGB

G.SKILL TridentZ Series 32GB (2 x 16GB) (F4-3200C14D-32GTZ)

PNY Quadro NVS 295 (cheap basic card)
Back to Top
Joe_Lewis View Drop Down
Newbie
Newbie
Avatar

Joined: 10 Sep 2020
Status: Offline
Points: 37
Post Options Post Options   Thanks (0) Thanks(0)   Quote Joe_Lewis Quote  Post ReplyReply Direct Link To This Post Posted: 12 Sep 2020 at 6:54pm
Is the GPU getting power (PCIe power connector ?)
Back to Top
jefarr View Drop Down
Newbie
Newbie


Joined: 12 Sep 2020
Status: Offline
Points: 5
Post Options Post Options   Thanks (0) Thanks(0)   Quote jefarr Quote  Post ReplyReply Direct Link To This Post Posted: 14 Sep 2020 at 7:47am
Thanks for the suggestion, but in this case the GPU doesn't take any additional power. This system is a linux server and I've only got the GPU installed for practical purposes installing and configuring the build.


I just finished switching out the RAM for a stick that is specifically Ryzen compatible and matches the specs listed in the QVL... but still no joy.

Honestly at this point I'm just going to ditch AsRock systems completely. It's been a while since I've built a computer, but I'm not at all new to building AMD systems and this just feels like a QA issue that I'd rather not have to deal with.


https://www.amazon.com/gp/product/B0023B132S/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1

https://www.newegg.com/g-skill-32gb-288-pin-ddr4-sdram/p/N82E16820232752?Item=N82E16820232752
Back to Top
Xaltar View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 16 May 2015
Location: Europe
Status: Online
Points: 24743
Post Options Post Options   Thanks (0) Thanks(0)   Quote Xaltar Quote  Post ReplyReply Direct Link To This Post Posted: 14 Sep 2020 at 1:57pm
It sounds like your Quadro card is a bit dated. By your description it appears the
system is POSTing but the display isn't getting the correct signal. The NVS 295 is
a PCIe Gen 1 device. Before you write off your board I would try with another, more
modern GPU. I know my old 9500 GT (same era) tester GPU works on even my X570 boards
but that is a PCIe Gen 2 device even though it shares the same basic architecture
as the NVS 295. The 295 is also a workstation card that has workstation specific
features that a mainstream board may not like.

GPU compatibility across PCIe generations isn't guaranteed, we often see older GPUs
simply not work on newer boards and newer ones not working on older systems.

Edited by Xaltar - 14 Sep 2020 at 2:27pm
Back to Top
jefarr View Drop Down
Newbie
Newbie


Joined: 12 Sep 2020
Status: Offline
Points: 5
Post Options Post Options   Thanks (0) Thanks(0)   Quote jefarr Quote  Post ReplyReply Direct Link To This Post Posted: 15 Sep 2020 at 5:38am
Ah, ok that's super helpful information and lines up with the observed behavior of the system. I wasn't aware of the PCIe compatibility, and at one point I was troubleshooting my monitor (ultrawide) for potential compatibility issues so intuitively this feels promising.

I'll give this a shot and report back.
Back to Top
the-cox View Drop Down
Newbie
Newbie


Joined: 13 Nov 2024
Status: Offline
Points: 30
Post Options Post Options   Thanks (0) Thanks(0)   Quote the-cox Quote  Post ReplyReply Direct Link To This Post Posted: 13 Nov 2024 at 3:36am
I got. the same issue with PSC VGA led Keepern red, but Unding a Ryzen 7 5700G 3.8 GHz with integrated graphics , what Clan I do, Power is supplied to all Ports
Cheeseburger, the cox
Back to Top
the-cox View Drop Down
Newbie
Newbie


Joined: 13 Nov 2024
Status: Offline
Points: 30
Post Options Post Options   Thanks (0) Thanks(0)   Quote the-cox Quote  Post ReplyReply Direct Link To This Post Posted: 13 Nov 2024 at 4:02am
I also tried it with a Gforce GTX1060 same issue??could is be that the motherboard was Not used for 18 month, it was originally packed
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 0.141 seconds.