FM2A58M-VG3+ R2.0 no post |
Post Reply | Page 12> |
Author | |
Xaltar
Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 24713 |
Post Options
Thanks(0)
Posted: 28 Jun 2015 at 12:49pm |
The best thing to do when there are bent pins on the CPU is take it back to where you bought it. If you are lucky they will replace it. If not then trying to straighten them is a very difficult task.
If the pins are flattened then it may not even be possible to straiten them without breaking them off. Good luck
|
|
ComputerCraze
Newbie Joined: 19 Jun 2015 Status: Offline Points: 20 |
Post Options
Thanks(0)
|
Took out the CPU and there were some bent pins. Is there any way to position them correctly?
|
|
Xaltar
Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 24713 |
Post Options
Thanks(0)
|
Ok, now you have a new PSU lets start at the beginning. I want you to take everything apart again as it was before you built the system, all cables, components, everything off the motherboard then:
1. Check your CPU pins, make sure none are bent or broken 2. Once you are sure the CPU pins are ok, insert it into the motherboard socket carefully and install the heatsink. 3. Insert your RAM into slot 1 4. Install the motherboard into the case being sure that the mounting standoffs are all in the right places and that there are no extra ones shorting circuits at the bottom of the motherboard. 5. Connect the Power Supply 24 pin power connector to the board and the 4 pin power connector near the boards VGA and DVI ports. 6. Connect the power switch to the motherboard power pins 7. Connect your monitor, keyboard and mouse to the system and power it up. If this fails then it is likely that that old power supply may have damaged the motherboard or it was faulty from the start. Post back your results and we can see what to do from there. Good luck
|
|
ComputerCraze
Newbie Joined: 19 Jun 2015 Status: Offline Points: 20 |
Post Options
Thanks(0)
|
Sadly, there is still no post
I got a Diablotek DA Series 400-Watt ATX Power Supply PSDA400 psu, installed it and there is still no post, however, everything else that I hooked up works fine. Hard drive, floppy drive, even the cpu fan. Maybe it's something with the motherboard?
|
|
Xaltar
Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 24713 |
Post Options
Thanks(0)
|
Good luck, I look forward to hearing good news
|
|
ComputerCraze
Newbie Joined: 19 Jun 2015 Status: Offline Points: 20 |
Post Options
Thanks(0)
|
Thank you so much! I will order a new PSU and get back to you.
|
|
Xaltar
Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 24713 |
Post Options
Thanks(0)
|
The system should work with 1 stick without issue.
I am still suspecting the power supply to be honest. That PSU was designed for use with a pentium 4 system, a lot has changed since then.
|
|
ComputerCraze
Newbie Joined: 19 Jun 2015 Status: Offline Points: 20 |
Post Options
Thanks(0)
|
Already tried that with no success. Could it be that two sticks of ram are required?
|
|
Xaltar
Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 24713 |
Post Options
Thanks(0)
|
KVR1333D3N9H/8G, is listed on your Motherboard RAM support list so it shouldn't be the RAM causing the issue. The H at after the 9 is a naming convention denoting where the particular RAM was made that has since been dropped so the one you listed is the same RAM.
I want you to remove the GT 610 from the system and try and boot again off the onboard (APU). I suspect your power supply may be inadequate to the task. If it works without the GT 610 installed then its a pretty safe bet your PSU is under-powered.
|
|
ComputerCraze
Newbie Joined: 19 Jun 2015 Status: Offline Points: 20 |
Post Options
Thanks(0)
|
Thanks for the input. I am using an old Compaq Presario S5100NX case for the build to save money, so I sadly don't have a speaker to connect to the motherboard. Is there another way to hear beeping (if any)?
I tried putting the RAM in a different slot and there was still no video out. My RAM is Kingston ValueRAM model no: KVR1333D3N9/8G. Thank you for the help, hopefully we can solve this
|
|
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |