ASRock.com Homepage
Forum Home Forum Home > Technical Support > Intel Motherboards
  New Posts New Posts RSS Feed - ASRock Q1900M no BIOS output
  FAQ FAQ  Forum Search Search  Events   Register Register  Login Login

ASRock Q1900M no BIOS output

 Post Reply Post Reply
Author
Message
mwgong View Drop Down
Newbie
Newbie


Joined: 23 Jul 2015
Status: Offline
Points: 5
Post Options Post Options   Thanks (0) Thanks(0)   Quote mwgong Quote  Post ReplyReply Direct Link To This Post Topic: ASRock Q1900M no BIOS output
    Posted: 23 Jul 2015 at 10:11pm
I just installed a new ASRock Q1900M motheboard.
 
When I power it on, the front panel light is on and the case fan runs, but there is no any output on monitor, like BIOS information.
 
Any idea what might go wrong ?
 
 
Back to Top
odiebugs View Drop Down
Newbie
Newbie


Joined: 07 Jul 2015
Status: Offline
Points: 193
Post Options Post Options   Thanks (0) Thanks(0)   Quote odiebugs Quote  Post ReplyReply Direct Link To This Post Posted: 23 Jul 2015 at 10:21pm
Which port are you using to monitor, have you tried DVI. 

Make sure the monitor setting is the same one you use on board, monitor must be set to DVI if it's plugged into DVI.

Was the memory off the QVL,  and have you tried only one stick to test the board ?


Edited by odiebugs - 23 Jul 2015 at 10:22pm
asrocking
Back to Top
Xaltar View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 16 May 2015
Location: Europe
Status: Offline
Points: 24518
Post Options Post Options   Thanks (0) Thanks(0)   Quote Xaltar Quote  Post ReplyReply Direct Link To This Post Posted: 23 Jul 2015 at 10:54pm
The problem is likely memory incompatibility, if possible try some different RAM. The Q1900M only supports DDR3 1333 RAM (you can use higher but it will not run at it's rated speeds). If the RAM is rated at a voltage higher than 1.5v you can have compatibility problems on these boards as they only support 1.35 and 1.5v RAM. While some 1.65v modules will work they will work at 1.5v and could prove unstable in some cases. 
Back to Top
mwgong View Drop Down
Newbie
Newbie


Joined: 23 Jul 2015
Status: Offline
Points: 5
Post Options Post Options   Thanks (0) Thanks(0)   Quote mwgong Quote  Post ReplyReply Direct Link To This Post Posted: 24 Jul 2015 at 12:02am
Since I don't have DVI cable, I connected to monitor using VGA and HDMI.
 
This is the memory I used:
Back to Top
odiebugs View Drop Down
Newbie
Newbie


Joined: 07 Jul 2015
Status: Offline
Points: 193
Post Options Post Options   Thanks (0) Thanks(0)   Quote odiebugs Quote  Post ReplyReply Direct Link To This Post Posted: 24 Jul 2015 at 2:49am
You can't use that memory, it's ECC.  Also you should use two or four sticks as you'll run in dual channel.

But if you only want one stick that's ok, just letting you know.

Please try to get memory off this list. 



I don't know if you can buy from here but this good memory and low price. 



Plus it only 23.00 US and 4g not 2g.






Edited by odiebugs - 24 Jul 2015 at 2:59am
asrocking
Back to Top
mwgong View Drop Down
Newbie
Newbie


Joined: 23 Jul 2015
Status: Offline
Points: 5
Post Options Post Options   Thanks (0) Thanks(0)   Quote mwgong Quote  Post ReplyReply Direct Link To This Post Posted: 24 Jul 2015 at 9:51pm
you are right. After I change with a non-ECC memory, the problem goes away.
 
Thanks.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 0.266 seconds.