![]() |
AMD Ryzen Compatible Memory List |
Post Reply ![]() |
Page <1 14151617> |
Author | |
cx5 ![]() Senior Member ![]() Joined: 15 Sep 2017 Location: Hong Kong Status: Offline Points: 2398 |
![]() ![]() ![]() ![]() ![]() |
hello @solarwnz
Your problem is somewhere else and you can make them work with manual settings. switching to other rams listed in QVL will not necessary work because you run too many ram...... i.e. first you have to know about this rule, apply to both Intel and AMD, see this link http://forum.asrock.com/forum_posts.asp?TID=15975&KW=&PID=79200&title=memory-clock-on-asrock-x570-creator#79200 and get tips from this link http://forum.asrock.com/forum_posts.asp?TID=15975&KW=&PID=79223&title=memory-clock-on-asrock-x570-creator#79223 this helps too http://forum.asrock.com/forum_posts.asp?TID=15699&KW=&PID=79187&title=ab350-gamingitx-ac-tridentz-16gb-only-2133-mhz#79187 finally this http://forum.asrock.com/forum_posts.asp?TID=15975&KW=&PID=79186&title=memory-clock-on-asrock-x570-creator#79186 Good luck. |
|
x370taichi@3.50gen4
AX750 Optane900P SN770 3800x PosdonZro4 BarrowPWM-17w>420x140x28 XFX SWFT319 6900XT MSI RX560 LP to get Fluid Motion BlueskyFRC 75hz |
|
![]() |
|
Mr Right ![]() Newbie ![]() ![]() Joined: 11 Sep 2020 Status: Offline Points: 10 |
![]() ![]() ![]() ![]() ![]() |
Boot Loop issues can be due to RAM but that seemed to being mainly an issue with 1st gen ryzen cpu's. You do not specify which gen CPU you are using but each generation of CPU seems to be less ram finicky than the prior. Why are you holding back on the bios upgrades if I might ask. A lot of time I would upgrade the bios to fix crashing during POST. Other things that can cause a boot loop are PSU and Video cards.
|
|
X470 Gaming K4
Ryzen 3600 32GB Z Neo 3600 c16-19-19-39 Bios 4.20 |
|
![]() |
|
Mr Right ![]() Newbie ![]() ![]() Joined: 11 Sep 2020 Status: Offline Points: 10 |
![]() ![]() ![]() ![]() ![]() |
Your board can handle 4 sticks of ram either single or dual rank but running 4 sticks they only guarantee stability at slower speeds. The CPU runs the ram stock 3200 mhz with 1 stick or 2 sticks paired in the right slots either Single ranked or Dual Ranked. when you go to 4 sticks of either single or dual ranked it slows the stock speed it guarantees down to 2933 for 4 SR chips or 2667 mhz for 4 DR chips. You might be able to run them faster all the way up to 4333 but it would require a nice PSU and some luck maybe a touch of voltage.
UDIMM Memory Slot Frequency A1 A2 B1 B2 (Mhz) - SR - - 3200 - DR - - 3200 - SR - SR 3200 - DR - DR 3200 SR SR SR SR 2933 SR/DR DR SR/DR DR 2667 SR/DR SR/DR SR/DR SR/DR 2667 |
|
X470 Gaming K4
Ryzen 3600 32GB Z Neo 3600 c16-19-19-39 Bios 4.20 |
|
![]() |
|
Mr Right ![]() Newbie ![]() ![]() Joined: 11 Sep 2020 Status: Offline Points: 10 |
![]() ![]() ![]() ![]() ![]() |
even though xmp is an intel marketing term it will still load the xmp profile settings just fine.
|
|
X470 Gaming K4
Ryzen 3600 32GB Z Neo 3600 c16-19-19-39 Bios 4.20 |
|
![]() |
|
mcfads1 ![]() Newbie ![]() Joined: 04 Dec 2020 Status: Offline Points: 1 |
![]() ![]() ![]() ![]() ![]() |
Hello! I'm running into some trouble with my build. I'm trying to upgrade from AMD Ryzen 2700x to 5800x
Motherboard: X570 Pro4 Asrock CPU: AMD Ryzen 5800x Upgrading from AMD Ryzen 2700x Issue: When I turn it on, everything turns on, fans spin, Red Light on VGA and DRAM. All my parts work on my Ryzen 2700x. We have updated the bios to the latest version We reset the CMOS We have tried different ram slots and singular ram (even though its working on those slots with the 2700) Anyone have an idea as to what I should do? I'm a bit lost and documentation is kind of bad We have tried everything in this post: http://forum.asrock.com/forum_posts.asp?TID=17204 I'd appreciate some guidance here? |
|
![]() |
|
Tropnas ![]() Newbie ![]() Joined: 14 Dec 2020 Status: Offline Points: 1 |
![]() ![]() ![]() ![]() ![]() |
Hello, I have problems running with upgraded RAM. Mouse is lagging, in games it shows 140 - 400 fps but it looks like 30 fps when im moving camera, movement feels not smooth, blurry, graphics, objects refresh slowly like 30 or less fps. Tested in MS Paint moving object and its same thing. I have 165 HZ monitor.
CPU 3700x, Asrock B450M PRO, GTX 1060, SSD Samsung 850 EVO SATA. Tested on 3.60 and 4.60 BIOS. Windows 10 v. 20H2. Problems with old BLS8G4D240FSB RAM enabling XMP, and same problem with new RAM BL2K8G36C16U4B and PVB416G360C7K on auto and XMP, tried many different settings, speeds CR1 and CR2, still does not work normal, lags. Works ok with BLS8G4D240FSB on auto, but when I try to enable XMP it works bad, and then switching to auto don't help, so I have to switch RAM slots, and the put back again to work normal. Maybe someone had similar problem, please help, I don't know what else I can do. |
|
![]() |
|
midnightcruise ![]() Newbie ![]() ![]() Joined: 21 Oct 2019 Location: Hilliard, Ohio Status: Offline Points: 12 |
![]() ![]() ![]() ![]() ![]() |
This is my solution for using 3600 GSKILL GTZRC memory. I believe the memory is Hynix CJR or DJR RAM and DRAM Calculator for Ryzed showed the tRP timing, SOC, VDDGG and VDDP voltages were all improperly set by the BIOS and XPM.
I have 2 different systems and they both had issues getting RAM work at any speed over SPD 2133. I spent some time figuring it out and wanted to share this post so others my benefit. Problems witnessed: Reboots would hang the system with BIOS code 8d. System would not ran stable with memory clocked over 3200. Would have to reset the BIOS some times just to get booted again. After making Memory timing and voltage changes below, both systems have been running flawlessly at 3600 with Fabric Clock at 1800. Clean reboots and stability have been achieved! Motherboard: Asrock AQUA X570 BIOS: 3.30 CPUs: 3950x 100-100000051WOF and 3900X 100-100000023BOX Video Card: ASUS ROG Strix RTX 2070 ROG-STRIX-RTX2070-O8G-GAMING Storage: SSD Samsung 970 EVO PLUS M.2 Memory: 64GB of G.Skill Trident Z RGB F4-3600C16Q-64GTZRC Operating System: Windows 10 20H2 load the XPM profile and changing the following settings: Memory timing tRP from 19 to 21 DRAM Voltage (should already be set by XPM) 1.35 SOC Voltage 1.03 VDDG (CCD and IOD) 1.00 cLDO VDDP Voltage 0.90 DRAM Frequency 3600 Infinity Fabric Frequency 1800 Optionally: I locked my PCIe to GEN3... not sure if this did anything to help. There may be other adjustments that would improve speed, but I am happy with this... good stability and performance is well above average for the configuration. Hope this helps out others! |
|
![]() |
|
Mikhail k ![]() Newbie ![]() ![]() Joined: 26 Jan 2021 Location: Syberia Status: Offline Points: 1 |
![]() ![]() ![]() ![]() ![]() |
good day to all. I have a problem. I bought: ASRock b550m itx ac motherboard; ryzen 3100 processor. G. skill FlareX F4-3200C14D-16GFX memory. the problem is that the PC does not start because of the memory. tried another pc memory starts up. we updated the bios and it didn't help. maybe someone had such a problem. the memory on the g. skill site is compatible with my motherboard. on the ASRock website, there are only cl16 3200 compatible memory from different manufacturers.
|
|
![]() |
|
aujlaakaran0 ![]() Newbie ![]() Joined: 13 May 2021 Status: Offline Points: 30 |
![]() ![]() ![]() ![]() ![]() |
I have a B350 Pro4 and I use EVGA 3000 memory.
|
|
![]() |
|
aujlaakaran0 ![]() Newbie ![]() Joined: 13 May 2021 Status: Offline Points: 30 |
![]() ![]() ![]() ![]() ![]() |
Good day to all.
NOTE: I HAVE EDIT OUT THE RANDOM UNASSOCIATED LINK YOU POSTED. IN THE FUTURE PLEASE DO NOT POST LINKS THAT DO NOT RELATE. HUMBLY, wardog Edited by wardog - 25 May 2021 at 2:08am |
|
![]() |
Post Reply ![]() |
Page <1 14151617> |
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |