![]() |
Z77 Pro3, Pro4 PCIE2 port doesn't work |
Post Reply ![]() |
Page <1 234 |
Author | |
GYUUHH ![]() Newbie ![]() Joined: 21 Jun 2015 Status: Offline Points: 9 |
![]() ![]() ![]() ![]() ![]() |
Tried cleaning the contacts and pre-installing the driver. still nothing.
As you know, then the PC is turned on, there is not signal. However, I know it is still loading to windows because i can hear it starting up through the speakers.
|
|
![]() |
|
Xaltar ![]() Moderator Group ![]() ![]() Joined: 16 May 2015 Location: Europe Status: Offline Points: 25478 |
![]() ![]() ![]() ![]() ![]() |
I'm sorry but that was the last suggestion I had. With no way to test if the 280x is actually functional we can't know for sure where the problem is coming from.
If no GPU was working in the system I would suggest reseating the CPU as the PCIE lanes are built into it but the 570 works so....
|
|
![]() |
|
GYUUHH ![]() Newbie ![]() Joined: 21 Jun 2015 Status: Offline Points: 9 |
![]() ![]() ![]() ![]() ![]() |
So I was able to try it on an older system but it still did not work. Fans spun but no video. It also did not have onboard video so I couldnt check if it was being detected.
Again the PC was rather old and it probably needed a BIOS update but I did not want to compromise the stability of someone elses PC just to test this.
|
|
![]() |
|
Xaltar ![]() Moderator Group ![]() ![]() Joined: 16 May 2015 Location: Europe Status: Offline Points: 25478 |
![]() ![]() ![]() ![]() ![]() |
At this point I would say the 280x is probably a dud
![]() I hope you are able to return it.
|
|
![]() |
|
ASRock_TSD ![]() ASRock_Official ![]() Joined: 20 Mar 2015 Status: Offline Points: 8802 |
![]() ![]() ![]() ![]() ![]() |
Dear all, this is ASRock Technical Support Department.
We have read all the replys, and decide to do the test for this issue. We tested using i5-2500(Sandy Bridge) and R9-270X(Gen3 card) with BIOS P1.80. The graphic card can run properly with above config, please refer the picture as below: ![]() Noted that the card is running at x16 speed, which mean it is installed in PCIE2 slot. Therefore, it seems like not a compatible issue between this board and the graphics card. For users who meet this issue, we provide some suggestions for try: 1. Since the PCIE resource is from CPU, please reinstall the CPU then check whether there?�s any bent or broken pins in CPU socket. 2. Unplug the power cable to do the clear CMOS settings. 3. If possible, please use another CPU or Gen3-graphics card to verify. 4. If the problem still, please replace the motherboard or the graphics card to verify. Thank you for your patience. Kindest Regards, ASRock TSD
Edited by ASRock_TSD - 01 Jul 2015 at 10:42am |
|
![]() |
|
Steiner06 ![]() Newbie ![]() Joined: 30 May 2015 Status: Offline Points: 5 |
![]() ![]() ![]() ![]() ![]() |
I tested and checked everything to get my Gigabyte GTX 970 G1 Gaming working on the Z77 Pro4 but no chance. The card is only detected on PCIE3 but not in the proper PCIE2 X16 Slot..
I wrote an email to the support center from asrock but the answer was exact the same as here. Is it possible that you guys can check this combination to? My CPU: i5-2500k PSU: Corsair CX750M GPU: Gigabyte GTX 970 G1 Gaming (newest VBIOS) MB: Asrock z77 Pro 4 (1.80) |
|
![]() |
|
GYUUHH ![]() Newbie ![]() Joined: 21 Jun 2015 Status: Offline Points: 9 |
![]() ![]() ![]() ![]() ![]() |
Card was RMA's and replaced with a brand new R9 390x. Installed and booted up without a hitch. All is well!
I'll take that trade any day =)
|
|
![]() |
|
Xaltar ![]() Moderator Group ![]() ![]() Joined: 16 May 2015 Location: Europe Status: Offline Points: 25478 |
![]() ![]() ![]() ![]() ![]() |
That's great news GYUUHH, enjoy your new GPU
![]() |
|
![]() |
Post Reply ![]() |
Page <1 234 |
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |