ASRock.com Homepage
Forum Home Forum Home > Technical Support > Intel Motherboards
  New Posts New Posts RSS Feed - B760 Pro RS // DRAM light Solid Red
  FAQ FAQ  Forum Search Search  Events   Register Register  Login Login

B760 Pro RS // DRAM light Solid Red

 Post Reply Post Reply
Author
Message
Gary0720 View Drop Down
Newbie
Newbie


Joined: 16 May 2024
Status: Offline
Points: 50
Post Options Post Options   Thanks (0) Thanks(0)   Quote Gary0720 Quote  Post ReplyReply Direct Link To This Post Topic: B760 Pro RS // DRAM light Solid Red
    Posted: 16 May 2024 at 2:48pm
My Rig suddenly failed to boot up. At a recent startup I found the DRAM light is solid red, and no screen inputs. The Rig is now installled with 2x DDR5 6000 RAMs.

When I installed the motherboard along with the new Drams I mistakenly placed the rams at the left 2 slots:

    ([1] [2] 3 4 , A1 and A2, I suppose?) .

Before this incident, the system need a longer period to boot up, but eventually IT WILL successfully boot up and the system works just as normal.

However during the latest boot the system just not showing any output. After I hit the Power On button on my rig, all the POST LED lihgts blinked, and only the DRAM light remains solid red.
Later on I tried re-arrange the DRAMs to the correct layouts:

    ( 1 [2] 3 [4], A2 and B2 respectively)

but the system still have no video outputs and thus I have no access to the BIOS interface. I failed to perform a BIOS flashback cause I cannot find the slot or the BIOS Flashback button on the motherboard.

Is there any clues of solving it?
Back to Top
Xaltar View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 16 May 2015
Location: Europe
Status: Offline
Points: 24398
Post Options Post Options   Thanks (1) Thanks(1)   Quote Xaltar Quote  Post ReplyReply Direct Link To This Post Posted: 16 May 2024 at 2:58pm
Try a single RAM module is slot A2, clear CMOS and power on. If it still won't
POST (show a display with the ASRock logo) then try the other module in slot A2.

If neither module brings up the POST screen then try disconnect the system from
power, pull the CMOS battery, press and hold the power button for 5 - 10 seconds
and leave the system like that for 10 mins or so. You can then replace the battery
and reconnect power to the system and try again.

If this also fails then you can see about trying with another power supply. There
is a chance your existing power supply is faulty and causing the system to hang
during POST (power on self tests) at the RAM testing phase.

If after all this you still have a non functional system then it's likely your CPU
may have died, more specifically the IMC (integrated memory controller) on the
CPU. If the CPU is still under warranty it will be covered for return/replacement.
Hopefully that isn't the case but sadly it is fairly common on CPUs these days.

Good luck
Back to Top
Gary0720 View Drop Down
Newbie
Newbie


Joined: 16 May 2024
Status: Offline
Points: 50
Post Options Post Options   Thanks (0) Thanks(0)   Quote Gary0720 Quote  Post ReplyReply Direct Link To This Post Posted: 16 May 2024 at 3:12pm
Thanks for the reply!

Some updates:

I tried change the CMOS battery and using a single slot DRAM at B2 ( 1 2 3 [4] ) made a successfull boot up into the BIOS, at first the DRAM light still solid red, but later DRAM light goes dark and BOOT and VGA light became solid red for a few seconds, then all 4 lights gone, the system boot up and goes into BIOS interface.

I suspect one of the two DRAM cards is broken but I'm not sure. While writing this post I'm trying to reboot the system again with both DRAM cards inserted at A2 and B2 DIMM slots.
Back to Top
Gary0720 View Drop Down
Newbie
Newbie


Joined: 16 May 2024
Status: Offline
Points: 50
Post Options Post Options   Thanks (0) Thanks(0)   Quote Gary0720 Quote  Post ReplyReply Direct Link To This Post Posted: 16 May 2024 at 4:07pm
Update:

I figure out the issue. One of my DRAM card failed. When both of them were plugged into the MB(motherboard) the motherboard shows a solid red light at DRAM and thus cannot enter BIOS mode. I tested in two ways: testing both DRAMs at the same DIMM socket, and test each of them at different socket. Turns out all slots on MB works perfectly fine, but one of my DRAM cards broken.

Hmm considering I just bought it a month ago that's really weird...
FYI those are CORSAIR VENGEANCE DDR5 16GB cards
. I just wonder why one of the two fails, but that's a different story.
Back to Top
Xaltar View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 16 May 2015
Location: Europe
Status: Offline
Points: 24398
Post Options Post Options   Thanks (0) Thanks(0)   Quote Xaltar Quote  Post ReplyReply Direct Link To This Post Posted: 16 May 2024 at 4:59pm
Just unlucky, it happens. This is why there is a warranty. Most often tech components
will fail inside a month, if not, they tend to be fine for ages. It all has to do
with how things like RAM chips are binned (sorted). Each chip is tested and put in
bins depending on how it performs, weaker chips get put on RAM modules with lower
frequencies and voltages where better ones get put on faster modules with more
voltage, different "bins".
Often a chip can pass the testing for a particular bin but fail shortly after because
it was not quite up to the task for 24/7 use.

Glad you got it sorted out
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 0.250 seconds.