![]() |
AM1H-ITX P1.50 - can't boot without a monitor? |
Post Reply ![]() |
Author | ||
myxal ![]() Newbie ![]() ![]() Joined: 01 Jun 2015 Status: Offline Points: 4 |
![]() ![]() ![]() ![]() ![]() Posted: 01 Jun 2015 at 5:26am |
|
I want to the motherboard for a small headless server. I got the system installed in UEFI mode, CSM is disabled in Setup, fastboot/secureboot/ultrafast boot are also all disabled.
With a monitor attached, everything works fine. Since the server will run headless, I checked if the system boots without a monitor - and it doesn't! The system powers up, but nothing happens. Attaching a monitor back again, a strange error appears: Obviously, I don't have a dedicated GPU installed, so why does this appear?
|
||
![]() |
||
Xaltar ![]() Moderator Group ![]() ![]() Joined: 16 May 2015 Location: Europe Status: Offline Points: 23993 |
![]() ![]() ![]() ![]() ![]() |
|
You have CSM disabled and it says does not support "CSM Disable". Try enabling CSM and see if you get anywhere.
If that fails then you can just turn the server on, wait for 10 seconds and hit F1 and it will continue to boot. Do you have your server set to auto wake or something? If not just hitting F1 at boot shouldn't be a problem.
|
||
![]() |
||
myxal ![]() Newbie ![]() ![]() Joined: 01 Jun 2015 Status: Offline Points: 4 |
![]() ![]() ![]() ![]() ![]() |
|
Yes, enabling CSM allows the system to boot without peripherals.
I'm just baffled by the error message - it's obviously wrong (there's no discrete VGA card in the system), and why does enabling CSM fix the issue anyway? My guess is that the UEFI firmware programmers made an assumption that if the onboard video outputs are all disconnected, then the user is using a discrete card, and the board searches for the GOP outside of its own firmware. It obviously can't find any, since there's no other graphics card! I hope Asrock fixes the problem in a future release. Just because there's an easy workaround doesn't mean that bugs in firmware are acceptable.
|
||
![]() |
||
Xaltar ![]() Moderator Group ![]() ![]() Joined: 16 May 2015 Location: Europe Status: Offline Points: 23993 |
![]() ![]() ![]() ![]() ![]() |
|
Ah, you didn't mention that you were not using a discrete GPU. I suspect you may be right as the way the system determines where to send the GPU output is by determining where the monitor is connected. Nice find, I am sure monitorless operation was not considered when designing the firmware
![]() |
||
![]() |
||
Shadow ![]() Newbie ![]() Joined: 09 May 2015 Status: Offline Points: 17 |
![]() ![]() ![]() ![]() ![]() |
|
I would suggest going into the UEFI and selecting onboard only as the output source. Since it looks to be set to auto, it's going to assume you have a discrete card is nothing is detected on the on-board connection. Once that is set, you should be able to go back to full UEFI boot
|
||
![]() |
||
davidyuen ![]() Newbie ![]() Joined: 21 Jul 2024 Status: Offline Points: 60 |
![]() ![]() ![]() ![]() ![]() |
|
my asrock EPC612D8A setting
1/CSM parameter Enabled 2/Full Screen Logo Enabled 2a/ Addon ROM display Disabled***. ***SAS ROM display would not freeze the bios. it can boot without monitor with P620 vga card to solaris 11.3 |
||
![]() |
||
davidyuen ![]() Newbie ![]() Joined: 21 Jul 2024 Status: Offline Points: 60 |
![]() ![]() ![]() ![]() ![]() |
|
|
||
![]() |
||
davidyuen ![]() Newbie ![]() Joined: 21 Jul 2024 Status: Offline Points: 60 |
![]() ![]() ![]() ![]() ![]() |
|
it can now be logined via realvnc viewer 5.3.3 |
||
![]() |
||
davidyuen ![]() Newbie ![]() Joined: 21 Jul 2024 Status: Offline Points: 60 |
![]() ![]() ![]() ![]() ![]() |
|
dont know how to delete the message
|
||
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |