Z690 Pro RS Not Posting

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

I just recently built a new pc, using the following gear:

MB: ASRock Z690 Pro RS (DDR4)
CPU: Intel i5-13500
Memory: G.Skill RipJaws V (DDR4) 2x16gb
Power Supply: EVGA G7 650w
(No GPU)

After connecting everything, I went to the ASRock website and downloaded the latest BIOS update, did the BIOS flashback, which was successful (no solid green light, light went off). After completion of BIOS flashback, I removed the USB drive with the new BIOS update, plugged in HDMI cable into the motherboard HDMI slot, and then turned on the PC. 

After clicking power button, DRAM red light stays on for a few seconds, then turns off, then VGA red light turns on, and about a second or so later, the BOOT red light turns on, and both VGA and BOOT red lights stay on for a few seconds before turning off.

A few attempts later, of reseating the RAM (using A2 and B2 slots), going down to 1 stick of RAM (and then swapping which stick is in the A2 slot), and now the motherboard after doing a light swap similar to the above listed lights, now keeps the VGA and BOOT lights on.

PC is never booting to motherboard splash screen/ability to access BIOS. Any thoughts on solutions? 

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
nuki Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 02 Oct 2024 Status: Offline Points: 20	Post Options Post Reply Quote nuki Report Post Thanks(0) Quote Reply Topic: Z690 Pro RS Not Posting Posted: 02 Oct 2024 at 10:52am
	I just recently built a new pc, using the following gear: MB: ASRock Z690 Pro RS (DDR4) CPU: Intel i5-13500 Memory: G.Skill RipJaws V (DDR4) 2x16gb Power Supply: EVGA G7 650w (No GPU) After connecting everything, I went to the ASRock website and downloaded the latest BIOS update, did the BIOS flashback, which was successful (no solid green light, light went off). After completion of BIOS flashback, I removed the USB drive with the new BIOS update, plugged in HDMI cable into the motherboard HDMI slot, and then turned on the PC. After clicking power button, DRAM red light stays on for a few seconds, then turns off, then VGA red light turns on, and about a second or so later, the BOOT red light turns on, and both VGA and BOOT red lights stay on for a few seconds before turning off. A few attempts later, of reseating the RAM (using A2 and B2 slots), going down to 1 stick of RAM (and then swapping which stick is in the A2 slot), and now the motherboard after doing a light swap similar to the above listed lights, now keeps the VGA and BOOT lights on. PC is never booting to motherboard splash screen/ability to access BIOS. Any thoughts on solutions?

Xaltar Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 24623	Post Options Post Reply Quote Xaltar Report Post Thanks(0) Quote Reply Posted: 02 Oct 2024 at 3:36pm
	https://forum.asrock.com/forum_posts.asp?TID=630&title=how-to-clear-cmos-via-battery-removal Try that. It sounds like you were POSTing but not getting a display output at the start. Now with the boot and VGA lights remaining on it sounds like you are getting stuck at the portion of POST that expects a display adapter (iGPU in your case). Clearing CMOS should fix that. Once done, if you still get no signal, try a different display output and/or cable. A bad or even just old HDMI cable can sometimes prevent a display output. Try the Display Port output from your board if you can/have not already.