|
Windows locks up after sleep after install dvd |
Post Reply 
|
| Author | |
knarley 
Newbie 
Joined: 14 Mar 2016 Status: Offline Points: 8 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Windows locks up after sleep after install dvdPosted: 05 Dec 2016 at 4:26am |
|
I just installed a DVD burner and now the computer locks up after sleep mode. It does not lock up every time but 1 out of 3 times it will. It did not do this before I installed the DVD. I also noticed that when I do a scan for hardware change in device manager it locks up too and it didn?™t before the DVD was installed. I am using an Asus DRW-24B1ST/BLK/B/AS Black SATA 24X DVD Burner and I also tried a Samsung 24X SH-224GB/BSBE and they both do the same thing. I tried both Windows 7 Pro and Windows 10 Pro both have the same problem. I tried looking for new firmware and driver for both DVD?™s but I did not find any. Right now I have the DVD unplugged and it has not locked up after sleep or when scanning for hardware changes. I searched Google for Windows problem with lock up after sleep but none of them fixed it and found nothing for DVD lock up after sleep so I am guessing it is something to do with the mother board or configuration.
ASRock Z170 Extreme7+ LGA 1151 Intel Z170 Intel Core i7-6700K 8M Skylake Quad-Core 4.0 GHz LGA 1151 91W BX80662I76700K EVGA GeForce GT 740 2GB Superclocked P/N: 02G-P4-3747-KR Video Card EVGA SuperNOVA 220-P2-0850-X1 850W Power Supply G.SKILL TridentZ Series 8GB (2 x 4GB) 288-Pin DDR4 SDRAM DDR4 3600 F4-3600C17D-8GTZ Transcend 256GB SATA III 6Gb/s MTS400 42 mm M.2 SSD Solid State Drive TS256GMTS400 WD Blue 1TB Desktop Hard Disk Drive |
|
|
Z170 Extreme7+ / Intel Core i7-6700K / GeForce GT 740
|
|
 |
|
|
wardog
Moderator Group 
Joined: 15 Jul 2015 Status: Offline Points: 6447 |
Post Options
Thanks(0)
Quote Reply
Posted: 05 Dec 2016 at 10:05am |
|
IMO this is either the cable / built in capacitor on the cable used to power BOTH drives, or, the PERIF1 or SATAx modular socket/connection on the side of the PSU. OR, your SATA data cable is defective, twisted. bent tight etc etc ......
But one drive, maybe. Yet two drives, no. It's more likely data cable or power related. |
|
|
|
|
parsec
Moderator Group
Joined: 04 May 2015 Location: USA Status: Offline Points: 4996 |
Post Options
Thanks(1)
Quote Reply
Posted: 05 Dec 2016 at 2:41pm |
|
Your board has two SATA controllers, the main Intel from the Z170 chipset, and the add on ASMedia SATA controller.
Which SATA port is the DVD drive connected to? The four ASMedia SATA ports are labeled 19 and 20 in the picture below:  If it is connected to any of the ASMedia SATA ports, move the SATA data cable to one of the Intel SATA ports. If it is connected to one of the Intel SATA ports, let us know, I may have an explanation for that too. Did you check the Windows Event and Error logs for any clues about this problem? |
|
|
|
|
|
|
knarley
Newbie
Joined: 14 Mar 2016 Status: Offline Points: 8 |
Post Options
Thanks(0)
Quote Reply
Posted: 05 Dec 2016 at 3:14pm |
|
I tried a different sata cable and power cable to DVD and it still locks up in device manager when I check for hardware changes. The DVD sata cable goes to #19 on the right and I just switched it to #15 on the left. I know how to get to the event viewer but I don't know what to look for when I get there. Where is the error log at? I am testing sleep mode now, it has to sleep for a while before it locks up.
Edited by knarley - 05 Dec 2016 at 3:19pm |
|
|
Z170 Extreme7+ / Intel Core i7-6700K / GeForce GT 740
|
|
|
|
|
Xaltar
Moderator Group
Joined: 16 May 2015 Location: Europe Status: Offline Points: 27113 |
Post Options
Thanks(0)
Quote Reply
Posted: 05 Dec 2016 at 3:19pm |
|
|
|
|
|
knarley
Newbie
Joined: 14 Mar 2016 Status: Offline Points: 8 |
Post Options
Thanks(0)
Quote Reply
Posted: 05 Dec 2016 at 3:27pm |
|
After switching sata cable to 15 left it no longer locks up in device manager when scanning for hardware changes. Still testing sleep mode.
|
|
|
Z170 Extreme7+ / Intel Core i7-6700K / GeForce GT 740
|
|
|
|
|
wardog
Moderator Group
Joined: 15 Jul 2015 Status: Offline Points: 6447 |
Post Options
Thanks(0)
Quote Reply
Posted: 05 Dec 2016 at 3:27pm |
If changing power and data cables didn't change this issue then my vote is for a defective drive. |
|
|
|
|
knarley
Newbie
Joined: 14 Mar 2016 Status: Offline Points: 8 |
Post Options
Thanks(0)
Quote Reply
Posted: 05 Dec 2016 at 3:32pm |
|
The sata cables are the ones that came with the mother board 26awg e320444 amw style 21149 80'c.
|
|
|
Z170 Extreme7+ / Intel Core i7-6700K / GeForce GT 740
|
|
|
|
|
knarley
Newbie
Joined: 14 Mar 2016 Status: Offline Points: 8 |
Post Options
Thanks(0)
Quote Reply
Posted: 05 Dec 2016 at 3:49pm |
|
Device manager when scanning for hardware changes works now in win 7 and win10 after switching to sata port 15 left. Still checking sleep mode so far it is working.
|
|
|
Z170 Extreme7+ / Intel Core i7-6700K / GeForce GT 740
|
|
|
|
|
knarley
Newbie
Joined: 14 Mar 2016 Status: Offline Points: 8 |
Post Options
Thanks(0)
Quote Reply
Posted: 06 Dec 2016 at 6:38am |
|
Thanks parsec problem solved.
|
|
|
Z170 Extreme7+ / Intel Core i7-6700K / GeForce GT 740
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
knarley wrote: