|
Hyper Quad M.2 Card Performance? |
Post Reply 
|
| Author | |
stonewater 
Newbie 
Joined: 03 Apr 2020 Status: Offline Points: 2 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Hyper Quad M.2 Card Performance?Posted: 03 Apr 2020 at 12:48am |
|
Of course I meant 'suspiciously like PCI3'.
|
|
 |
|
|
stonewater
Newbie
Joined: 03 Apr 2020 Status: Offline Points: 2 |
Post Options
Thanks(0)
Quote Reply
Posted: 03 Apr 2020 at 12:47am |
|
So I just tried installing 4 x Seagate Firecuda 520's in RAID 0 on the Hyper Quad and I'm getting writes topping out at 3.89GBps and reads at 5.22GB/s which looks suspiciously to me like PCI4.
This is on a TRX40 Taichi which comes with the hyper quad - in the ASrock recommended PCIE4. Did anyone else experience this / solve this? Thanks David |
|
|
|
|
bvalente
Newbie
Joined: 05 Sep 2018 Status: Offline Points: 9 |
Post Options
Thanks(0)
Quote Reply
Posted: 02 Mar 2020 at 11:48pm |
|
Thanks - is that 3x performance of?
Brian |
|
|
|
|
gizmic
Groupie 
Joined: 13 Jun 2018 Location: Hong Kong Status: Offline Points: 677 |
Post Options
Thanks(1)
Quote Reply
Posted: 02 Mar 2020 at 6:21pm |
|
actually quad raid 0 are closer to 3X performance
|
|
|
|
|
|
|
cx5
Senior Member 
Joined: 15 Sep 2017 Location: Hong Kong Status: Offline Points: 2398 |
Post Options
Thanks(0)
Quote Reply
Posted: 02 Mar 2020 at 3:06pm |
|
Hello Brian,
seq read 4747ï¼?sounds too low, should be this link multiply 4 = 7000Mb/s https://cdn.mos.cms.futurecdn.net/zY4mMsbYdA4JUC3ayDKGUm-970-80.png seq write 6115, sounds about right to me, because 660p is slow, only around 1700mb/s, https://cdn.mos.cms.futurecdn.net/FRZi4HbetMXCawprZFMsab-970-80.png so 4 card is 7000. If you get a HP EX950, write is 2900Mb/s then 4 card raid-0 is around 11000Mb/s those guys with very high transfer are using very fast NVMe like HP EX950 |
|
|
x370taichi@3.50gen4
AX750 Optane900P SN770 3800x PosdonZro4 BarrowPWM-17w>420x140x28 XFX SWFT319 6900XT MSI RX560 LP to get Fluid Motion BlueskyFRC 75hz |
|
|
|
|
bvalente
Newbie
Joined: 05 Sep 2018 Status: Offline Points: 9 |
Post Options
Thanks(0)
Quote Reply
Posted: 02 Mar 2020 at 11:03am |
|
It seems my hyper quad m2 raid array is pretty slow?
seq read 4747 seq write 6115 (as measured by crystaldiskmark) https://www.dropbox.com/s/sgqamkrc86zii97/crystaldisk.png?dl=0 this is 4x 1tb Intel 660p M2 cards in a raid 0 configuration I have seen specs of similar setups that are 115304 seq read doesn't have to match, but seems like it could be much faster? I'm pretty sure I have the firmware configured correctly, the card is in slot 3. the swap disks i have set up on the raid array are a constraint to performance on some of my most important apps Any feedback, suggestions, questions would be great thank you! Brian |
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options