H510 PRO BTC+

Hey what?™s up everyone!! Justa few things!
1 I also get a red x but I get a ?œmalfunction??on my hiveos, I haven?™t tried placing it on the 3rd port, but slot 1 seems to run fine. Didn?™t update bios (from my knowledge, other than that I?™m chillin!
I got 2 3060 ti 3x ventus (LHR), 1 3070(LHR), 1 3070 ti(LHR) 6800

Thanks!!

I have 2 other issues, the onboard video will not work( only allows the GPU video) and I cannot get the 1.40 drivers to download correctly. The nic on the board does initiate, the download starts, but it will not allow me to download it anywhere, IE USB Drive or External HD. It keeps hanging up after download. I sure wish I had a way that I could download the driver update for the board without using the internet flash. Any suggestions please? I would love to run more than one card sometime before the month is over.

Kenzo95 wrote: Okay, After mounted 29 H510 BTC Builds from 1 GPU to 10 GPUs I'm feel that i Had to give something to Asrock and Community for payback This is my little Tips to use the H510 PRO BTC+ -Ram MUST BE 8GB or more accord to the manual. -If you want a stable build with more than 6 GPU use a CPU with at least 4MB of cache like Pentium G6400 or more. -5 beeps Just indicate that the System hasn't detect a Monitor (maybe not attached or maybe wrong detection) -Connect 24 Pin connector and 8 CPU Pin Connectors -Follow the Signage A-A B-B C-C for power the PCIE slots -Motherboard HDMI doesn't work with HiveOS, after booting the OS doesn't load the GPU, so use HDMI or DP of first GPU. -You can Bifurcate the mining port 1 to 4 without problems. -If you want use RTX 3000 on HiveOS you MUST upgrade Bios to 1.30, 1.10 doesn't work well with them.

Did you manage to have more than 11 GPUs connected? I have 11 running but when I plug number 12 it boots directly into bios and OS can't be started, it seems a bios issue to me or some kind of limitation

* If I install GPUs in PCEI3, 4, 5 and 6 everything work as it should.

* If I also install a GPU in PCIE2 the system enters in the Bios and the only way to boot up is by manually going to EXIT -> Choosing the Manual SATA partition to boot from. It basically stops booting up automatically... No errors.

* If I also install a GPU in PCIE1 the BIOS beeps 8 times (Display memory error) and halts

* If I tried to install my 6 GPU in the USB Riser, nor the Bios or the Windows Device Manager shows the card installed.

---
This happens in two different H510 motherboards, using GPU 6900XT, 2 and/or 3 1600W PSU and the bios updated to the latest version available 1.4

Did anybody run into similar issues, any solutions/workarounds that you found? I tried setting the PCIes to GEN2, and plenty of other Bios setting, and no solutions so far...

ANY GOOD ADVICE IS MORE THAN WELCOME AT THIS POINT! THANK YOU ALL

Good evening colegues,

I have little issue with mb.

Last two months I managed to built 9 rigs with rtx 2060, 3090 and rx6600 sapphire pulse and they all worked out of the box.
Basicly update bios, all cards recognized, install hive and thats it.

I mentioned specific rx6600 sapphire because today I tried to built rig with 5x rx6600 xfx swft and I just cant get it to work. Same setup as previous rigs.
MB only recognize first 2 out of 5 gpus, and on 5th shows red light.

Any ideas?

I tried everything mentioned in thread and just cant it to work.


Any ideas?