|
Z170m PRO4S beep codes |
Post Reply 
|
Page <12 |
| Author | |
Cicca 
Newbie 
Joined: 26 May 2016 Location: Turin Status: Offline Points: 8 |
 Post Options
 Thanks(0)
 Quote Reply
 Posted: 27 May 2016 at 3:28am |
|
Just tried....nothing changes....that was not the problem.....
 Other ideas..?! |
|
 |
|
|
parsec
Moderator Group 
Joined: 04 May 2015 Location: USA Status: Offline Points: 4996 |
Post Options
Thanks(0)
Quote Reply
Posted: 27 May 2016 at 11:35am |
|
Have you done a UEFI/BIOS clear yet? You can do that by moving the jumper on the CLR_CMOS header. That header is on the lower edge of the board, on the right side.
Do you know how to do that? Be sure the PC is off, PSU is off and disconnected from AC power. |
|
|
|
|
|
|
Cicca
Newbie
Joined: 26 May 2016 Location: Turin Status: Offline Points: 8 |
Post Options
Thanks(0)
Quote Reply
Posted: 27 May 2016 at 2:22pm |
|
Yes, I did it twice....once before removing the video card (since I had moved the DIMMs from a slot to another), and then after.....same threee long beeps immediatly at the power up....
|
|
|
|
|
Xaltar
Moderator Group
Joined: 16 May 2015 Location: Europe Status: Online Points: 25073 |
Post Options
Thanks(0)
Quote Reply
Posted: 27 May 2016 at 2:38pm |
|
OK, now try removing the RAM from the system entirely and see if you get the same beep code without it. If the code is different then the RAM is not the problem.
|
|
|
|
|
|
|
Cicca
Newbie
Joined: 26 May 2016 Location: Turin Status: Offline Points: 8 |
Post Options
Thanks(0)
Quote Reply
Posted: 30 May 2016 at 2:33pm |
|
Hi....update status: removed both DIMMs (from slots A2/B2), cleared the CMOS, turned on.....same three beeps....
 ....turned off, mounted the DIMMs back, but in slots A1/B1, cleared the CMOS again, turned on....and....NO BEEPS....  Now....the new problem is that it doesn't seem to post/boot....I say "seem" because I have no proper cable to connect the monitor (the video card has a Dispay Port output, but the MB no, and the monitor has no HDMI input)....but I hear no "beep" between the POST and the boot (in any case, it can't boot anything since the HD is empty).... Now....what's your suggestion...?! Buy a cable, and see how it goes on....or try to mount the video card back....?! |
|
|
|
|
Xaltar
Moderator Group
Joined: 16 May 2015 Location: Europe Status: Online Points: 25073 |
Post Options
Thanks(0)
Quote Reply
Posted: 30 May 2016 at 2:54pm |
|
Try mount the video card and see how it goes. Good luck.
|
|
|
|
|
|
|
|
Cicca
Newbie
Joined: 26 May 2016 Location: Turin Status: Offline Points: 8 |
Post Options
Thanks(0)
Quote Reply
Posted: 03 Jun 2016 at 3:29pm |
|
YEAH !!! It goes !!! Thanks for all the help !!!
|
|
|
|
|
Xaltar
Moderator Group
Joined: 16 May 2015 Location: Europe Status: Online Points: 25073 |
Post Options
Thanks(1)
Quote Reply
Posted: 03 Jun 2016 at 4:08pm |
|
Glad to hear it, awesome job
|
|
|
|
|
|
|
|
Post Reply
|
Page <12 |
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options