Z170m PRO4S beep codes

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   Just tried....nothing changes....that was not the problem.....
Other ideas..?! 

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Cicca Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 26 May 2016 Location: Turin Status: Offline Points: 8	Post Options Post Reply Quote Cicca Report Post Thanks(0) Quote Reply Posted: 27 May 2016 at 3:28am
	Just tried....nothing changes....that was not the problem..... Other ideas..?!

parsec Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Joined: 04 May 2015 Location: USA Status: Offline Points: 4996	Post Options Post Reply Quote parsec Report Post Thanks(0) Quote Reply Posted: 27 May 2016 at 11:35am
	Have you done a UEFI/BIOS clear yet? You can do that by moving the jumper on the CLR_CMOS header. That header is on the lower edge of the board, on the right side. Do you know how to do that? Be sure the PC is off, PSU is off and disconnected from AC power.


Cicca Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 26 May 2016 Location: Turin Status: Offline Points: 8	Post Options Post Reply Quote Cicca Report Post Thanks(0) Quote Reply Posted: 27 May 2016 at 2:22pm
	Yes, I did it twice....once before removing the video card (since I had moved the DIMMs from a slot to another), and then after.....same threee long beeps immediatly at the power up....

Xaltar Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 25073	Post Options Post Reply Quote Xaltar Report Post Thanks(0) Quote Reply Posted: 27 May 2016 at 2:38pm
	OK, now try removing the RAM from the system entirely and see if you get the same beep code without it. If the code is different then the RAM is not the problem.


Cicca Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 26 May 2016 Location: Turin Status: Offline Points: 8	Post Options Post Reply Quote Cicca Report Post Thanks(0) Quote Reply Posted: 30 May 2016 at 2:33pm
	Hi....update status: removed both DIMMs (from slots A2/B2), cleared the CMOS, turned on.....same three beeps.... ....turned off, mounted the DIMMs back, but in slots A1/B1, cleared the CMOS again, turned on....and....NO BEEPS.... Now....the new problem is that it doesn't seem to post/boot....I say "seem" because I have no proper cable to connect the monitor (the video card has a Dispay Port output, but the MB no, and the monitor has no HDMI input)....but I hear no "beep" between the POST and the boot (in any case, it can't boot anything since the HD is empty).... Now....what's your suggestion...?! Buy a cable, and see how it goes on....or try to mount the video card back....?!

Xaltar Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 25073	Post Options Post Reply Quote Xaltar Report Post Thanks(0) Quote Reply Posted: 30 May 2016 at 2:54pm
	Try mount the video card and see how it goes. Good luck.


Cicca Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 26 May 2016 Location: Turin Status: Offline Points: 8	Post Options Post Reply Quote Cicca Report Post Thanks(0) Quote Reply Posted: 03 Jun 2016 at 3:29pm
	YEAH !!! It goes !!! Thanks for all the help !!!

Xaltar Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 25073	Post Options Post Reply Quote Xaltar Report Post Thanks(1) Quote Reply Posted: 03 Jun 2016 at 4:08pm
	Glad to hear it, awesome job