G31M-GS Ver2

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

I have a problem booting now with this board.
The pc turns on, as in the cpu and graphics card fans rotate, but getting no signal to the monitor, and no beeps. I have tried another working psu, graphics card, and memory sticks, but still get the same problem.
Could this be down to a problem with the PCI slot, or general motherboard issue?
At the moment all I have connected to the board is as followsMainboard
cpu/heatsink & fan
1 stick of Corsair xms memory
1 Asus GT640 Graphics card

I have all these parts connected not in a case, but on an antistatic mat, so as to rule out the case being the issue.

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Logicearl Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 14 Jul 2015 Location: UK Status: Offline Points: 7	Post Options Post Reply Quote Logicearl Report Post Thanks(0) Quote Reply Topic: G31M-GS Ver2 Posted: 14 Jul 2015 at 7:36pm
	I have a problem booting now with this board. The pc turns on, as in the cpu and graphics card fans rotate, but getting no signal to the monitor, and no beeps. I have tried another working psu, graphics card, and memory sticks, but still get the same problem. Could this be down to a problem with the PCI slot, or general motherboard issue? At the moment all I have connected to the board is as follows Mainboard cpu/heatsink & fan 1 stick of Corsair xms memory 1 Asus GT640 Graphics card I have all these parts connected not in a case, but on an antistatic mat, so as to rule out the case being the issue.

Xaltar Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 24653	Post Options Post Reply Quote Xaltar Report Post Thanks(0) Quote Reply Posted: 14 Jul 2015 at 11:08pm
	Try removing the GT640 and using the onboard VGA connector. Also try the RAM in each slot in turn. If you still get nothing you can try checking the CPU, remove it, check pins and contact pads and make sure they are clean. If you need to clean contact pads use isopropyl alcohol and an earbud. Good luck

Logicearl Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 14 Jul 2015 Location: UK Status: Offline Points: 7	Post Options Post Reply Quote Logicearl Report Post Thanks(0) Quote Reply Posted: 14 Jul 2015 at 11:16pm
	yes I have tried everything you have listed now apart from using the vga port. Will try that. But I don't want to just rely on just the onboard graphics. Thanks anyway.

parsec Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Joined: 04 May 2015 Location: USA Status: Offline Points: 4996	Post Options Post Reply Quote parsec Report Post Thanks(0) Quote Reply Posted: 15 Jul 2015 at 2:04am
	Is this the first time you are using this board with the parts you listed? What is the full model number of your memory, and what CPU are you using? Do you have a beep speaker connected to the board? It does not have one built in. You may need to set the video source to PCI Express in the BIOS. Using the onboard video is a test to see if the board will POST with the CPU and memory you have.

Logicearl Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 14 Jul 2015 Location: UK Status: Offline Points: 7	Post Options Post Reply Quote Logicearl Report Post Thanks(0) Quote Reply Posted: 15 Jul 2015 at 3:43am
	Is this the first time you are using this board with the parts you listed? No, these parts worked for a short time before this problem. What is the full model number of your memory, and what CPU are you using? I have now used 2 sets so far. 2 x Corsair XMS2 CM2X2048-6400C5C 2 x OCZ Platinum OCZ2P800R22GK The cpu is an Intel 2.8Ghz Do you have a beep speaker connected to the board? It does not have one built in. Yes it does has a "Beep Speaker". But so far It doesn't beep, including the post beep when powering up. You may need to set the video source to PCI Express in the BIOS. At the moment I cannot gain access to the BIOS to change anything. Using the onboard video is a test to see if the board will POST with the CPU and memory you have. I will see if I can find a VGA cable tomorrow. Thanks for everyones help.

Logicearl Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 14 Jul 2015 Location: UK Status: Offline Points: 7	Post Options Post Reply Quote Logicearl Report Post Thanks(0) Quote Reply Posted: 15 Jul 2015 at 4:59pm
	Right I have now tried connectting a brand new vga cable and stilll no joy. It doesn't seem to want to start. The only thing I hav'nt changed is the cpu, could this be the problem?

parsec Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Joined: 04 May 2015 Location: USA Status: Offline Points: 4996	Post Options Post Reply Quote parsec Report Post Thanks(0) Quote Reply Posted: 15 Jul 2015 at 7:22pm
	Did you try clearing the CMOS/BIOS yet? What BIOS version are you using, the latest is 1.90: http://www.asrock.com/mb/Intel/G31M-GS%20R2.0/?cat=Download&os=BIOS

Logicearl Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 14 Jul 2015 Location: UK Status: Offline Points: 7	Post Options Post Reply Quote Logicearl Report Post Thanks(0) Quote Reply Posted: 15 Jul 2015 at 8:05pm
	Yes I have tried clearing the cmos on numerous occasions. Cannot tell you which bios is installed, as I don't know. And as I can't access the bios, or anything come to that, I cannot see. Just to clarify what I have done so far. Up untill recently I have had this pc, running from new, about 1 month, old parts, but purchased new, Then one day I turn on the pc, but all that happens, is I get a no signal dialoge box on the monitor. The pc starts with all the fans operating normally, that is the cpu heat sink fan, the graphics card fan and a case fan. But there is no beep of any kind, so no post. I then took all the parts out of the case to eliminate that as being at fault, and connected the basic minimum on a antistatic mat. All the swopped parts are all know to work. I have also tried all the parts in another pc, and again they all work. I swap out the power supply, no change, I swap out the graphics card, no change, I swap out the memory, no change. I then buy a new vga cable to se if using the onboard graphics will get it to work, but again, no change. The only parts I havn't been able to swap out are the motherboard, and the cpu. It would seem to me that the problem lies with either the motherboard, or the cpu, or both. Is there any thing I can do to determine whats deffective, given what I've done already? Thoughts anyone?