![]() |
970a-g/3.1 + R9 16GB (4x4GB) DDR3 2133 problem |
Post Reply ![]() |
Page <123> |
Author | |
wardog ![]() Moderator Group ![]() Joined: 15 Jul 2015 Status: Offline Points: 6447 |
![]() ![]() ![]() ![]() ![]() |
![]() |
|
wardog ![]() Moderator Group ![]() Joined: 15 Jul 2015 Status: Offline Points: 6447 |
![]() ![]() ![]() ![]() ![]() |
Errr, um, maybe they are 1.5v Edited by wardog - 28 Jan 2017 at 1:22am |
|
![]() |
|
Zirw ![]() Newbie ![]() ![]() Joined: 25 Jan 2017 Status: Offline Points: 55 |
![]() ![]() ![]() ![]() ![]() |
Initially, I had a CPU NB voltage 1.1625 I changed just one step up to 1.1750. memory voltage in the auto mode is at the level of 1.65. As only reduce CPU NB voltage to 1.1625 computer does not start with four memory modules! I can take pictures of bios setup with which it works!
Excuse me! just I noticed that not sealed 1.75 I meant 1.175! Sorry
![]() Edited by Zirw - 25 Feb 2017 at 6:15am |
|
![]() |
|
wardog ![]() Moderator Group ![]() Joined: 15 Jul 2015 Status: Offline Points: 6447 |
![]() ![]() ![]() ![]() ![]() |
Until you set AMP/XMP their initial first post Mhz will be 1600. Remember, the memory is Dual Data Rate, DDR, so CPU-z will show "half' of the speed. So 800 = 1600 in reality.
Is the pic above this post taken with all four sticks installled? Notice below H/W Monitor, where it says DDR3_A1? Please also post pics of DDR3_A2, DDR3 _B1, and DDR3_B2. You do this by clicking on the DDR_A1 button and selecting the other three sticks location. |
|
![]() |
|
Zirw ![]() Newbie ![]() ![]() Joined: 25 Jan 2017 Status: Offline Points: 55 |
![]() ![]() ![]() ![]() ![]() |
![]() ![]() ![]() ![]() Edited by Zirw - 25 Feb 2017 at 6:43pm |
|
![]() |
|
wardog ![]() Moderator Group ![]() Joined: 15 Jul 2015 Status: Offline Points: 6447 |
![]() ![]() ![]() ![]() ![]() |
Type out here the settings you're changing when you say "OC the bus."
|
|
![]() |
|
wardog ![]() Moderator Group ![]() Joined: 15 Jul 2015 Status: Offline Points: 6447 |
![]() ![]() ![]() ![]() ![]() |
![]() |
|
Zirw ![]() Newbie ![]() ![]() Joined: 25 Jan 2017 Status: Offline Points: 55 |
![]() ![]() ![]() ![]() ![]() |
Memory takes 1765 when BUS
220. The power supply has changed recently at Templarius 850W 80+ Silver. PC is
connected to the UPS to 1500W. Processor card xf8350 GTX1070 16gb 4x4
unilateral AMD R9 bar. I decided to reduce timings :) course through the BIOS. Any change leads to the fact that the PC does not start. If you change the timings via AMD Overdrive everything OK! I checked again on another motherboard. My CPU is my graphics card and my two sets of memory and my power supply work. Memory starts all 4 bracket for 1866 and even at 2133Mhz. Tested on the MSI 970 Krait edition. Then to be sure I vzl old card GIGABYTE 760g and even the memory of it all 4 strips earned in 1866! Why is that? After 970a-g / 3.1 class above these motherboards? It's a marriage? I was about to accept, but I can not even reduce the timings! Almost any manipulation in the BIOS lead to the fact that the PC does not start. And with four bars, I can not clear the CMOS as the motherboard determines them as of 1866 and does not start with them. To reset the CMOS every time I have to take out the two memory strip. P.S. Do not even the
manufacturer BETA version of the BIOS? For all products on the 970 chipset came
out at least one update the BIOS? kromne 970a-g / 3.1 :) Edited by Zirw - 26 Feb 2017 at 12:52am |
|
![]() |
|
wardog ![]() Moderator Group ![]() Joined: 15 Jul 2015 Status: Offline Points: 6447 |
![]() ![]() ![]() ![]() ![]() |
Instead of OC'ing the bus, which brings many headaches, instead leave the bus at 200 and change the multiplier.
|
|
![]() |
|
wardog ![]() Moderator Group ![]() Joined: 15 Jul 2015 Status: Offline Points: 6447 |
![]() ![]() ![]() ![]() ![]() |
Oh, and put your HT back to 2000 or 2200 when changing the multiplier.
|
|
![]() |
Post Reply ![]() |
Page <123> |
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |