AMD FX 6300 overheats....

my whole pc is under 1 year old the corsairs currently in transit for  replacement  .

Edited by quagmire94 - 11 Mar 2017 at 8:06am

such questions.

Edited by quagmire94 - 11 Mar 2017 at 9:22am

quagmire94 wrote: 8:understood  but i do not mess with overclocking.

It is a requirement, overclocking or not, that a fan be situated and secured to blow over the VRMs when you water cool.

When you remove a "stock" HSF and replace it instead with a water pump there isn't any more airflow that the "stock' HS/F would supply to cool the VRMs.

And the installation instructions from Corsair in the box states a fan must be placed over the VRMs. Or it used to anyways. And for good cause, as I mention above.

quagmire94 wrote: such questions. VVVVVVV parsec   ^^^^^^^   snip!  3:not sure where u read this, this is not true. snip!

Where did I get the idea that the first time you put the PC together, it got hot and then turned off?

From you first post:

quagmire94 wrote:  so , my amd fx 6300 put a beating on my corsair h100i v2 .          i was playing overwatch and streaming  at the same time. my temp is normally  around 130 F. well when the corsair failed During game play my cpu went over 200 F  . now the BIOS loading screen of my Asrock 970M Pro3 has a strange effect when u boot Bios. my computer's motherboard is only around 4 months old too..... some strange reason the motherboard didn't enable thermal throttling  when i first put my pc together so it just got HOT and then turned off          i guess now im asking , what do i do. will this Visual affect turn into something where my computer will break ? i just need help.

I guess what you actually wrote, but due to the formatting did not come out right, and did not make sense to me, is:

"... some strange reason the motherboard didn't enable thermal throttling  when i first put my pc together so it just got HOT and then turned off  "

My questions are simply standard things that are basic PC building situations. I decided to ask all the questions now, instead of dragging them out over several pages of single questions and answers.

Let's look at your video card, a PNY 1060 6GB:




Sorry to say, no video card vents all its exhaust out the back vent. First we can see the gap around the sides and back of the card, the PC board is visible on the side, and part of the heat sink fins are visible at the back. Then the vent of the double slot height is not even two inches high. Those two 90mm - 100mm fans move more air than can be vented out those small vents. The video card is not sealed air tight to force the air out the back, even if it could all be vented out the back. Video card manufactures like to tell us all the heat vents out the back, but that is obviously not what happens.

The card hits 70C, that's low and great. I bet the fans don't even run at idle, or run very slow. But under stress, it is dumping most of the waste heat into the PC case, not out the back of the card. We wish it went out the back. Feel what is coming out the back of the card at that time.

Radiator location is a difficult thing to determine. One aspect will be perfect, but the other won't in most locations. Your exhaust is out the top which is great, but where is the air intake source?

You have one 120mm fan at the top rear, through a filter. All filter restrict air movement by at least half. It's also pulling air through the vents cut in the PC case, further restricting air flow. Feel the air flow into the case from that fan sometime, it will surprise you how little it is.

Your radiator has two 120mm fans for exhaust. You need to supply those fans with as much air as they exhaust, or they won't be able to exhaust it. You have one intake fan supplying less air than needed by one of the exhaust fans. Where does the other air come from?

From inside the PC case. It's the only other source. What happens during gaming? The video card heats up, and dumps most of its heat into the PC case. That warm air is sucked up into the radiator, and over the VRM heat sink. So you are cooling the radiator with air that is warmer than the air outside of the case.

If you check Corsair's instructions for the AIO coolers, it may surprise you to see they suggest intake mode for the radiator. That of course to to optimize the CPU temperature. It becomes our problem about what to do with that warm air, if we do it that way.

If you can put case fans in the front of your PC case, do it. You need to pump fresh air into that case. If you can put two fans in front, or even three, do it. Also, remove all of the PCIe slot covers from the back of the PC case. You now have vents for the video card heat, or at least more air intake area.

Consider, how can a 95W TDP processor, not over clocked, using a 240mm radiator, over heat during gaming? Why does the pump keep dying, apparently? What is powering the pump, a mother board fan header? Something is just not right here, and I have given you several examples why it isn't right.

psu is a thermaltake tr2 600w 4 months old  just like every other component on this pc. it's all brand new.

Edited by quagmire94 - 12 Mar 2017 at 8:02am