ASRock.com Homepage
Forum Home Forum Home > Technical Support > AMD Motherboards
  New Posts New Posts RSS Feed - x399 Taichi won't boot up
  FAQ FAQ  Forum Search Search  Events   Register Register  Login Login

x399 Taichi won't boot up
 Post Reply Post Reply Page  <12345 6>
Author
Message Reverse Sort Order
  Topic Search Topic Search  Topic Options Topic Options
sdlashley View Drop Down
Newbie
Newbie


Joined: 28 Sep 2017
Location: Portland OR
Status: Offline
Points: 19 		Post Options Post Options   Thanks (1) Thanks(1)   Quote sdlashley Quote  Post ReplyReply Direct Link To This Post Posted: 01 Oct 2017 at 11:21am
Today I got my EVGA G3 750 and now things are working perfectly.
As far as ram goes, the 128G of G Skill Flare 2133 is working great. Its cost me $1k for that. I didn't want to spring and extra $400-$500 to get 3200 cause it won't make that big a difference in what I do. But, thx for the suggestion.

My final setup is...
Ryzen 1950x
x399 ASrock Taichi
128G G Skill Flare X 2133
EVGA 750 G3 PSU
MSI GeForce GT 710
Fractal Design Celsius C24 Cooler
Fractal Design R5 Black Case
Samsung 960 EVO M2 500G (boot drive)
Samsung 960 Pro M2 1Tb (data drive)
Ubuntu 16.04 (had to go with this for compatibility reasons)
Total Cost $3449

I was able to get complete sensor info using gkrellm on Ubuntu 17.04. Still trying with 16.04
I have not been able to get WiFi to work. When I do Enable Wifi, it 

I want to personally thank misterj and datonyb for all their help!
Back to Top
raminro View Drop Down
Newbie
Newbie


Joined: 01 Oct 2017
Location: iran
Status: Offline
Points: 6 		Post Options Post Options   Thanks (0) Thanks(0)   Quote raminro Quote  Post ReplyReply Direct Link To This Post Posted: 01 Oct 2017 at 10:54am

ATTENTION

ATTENTION

boys boys

ON RYZEN ONLY USE DUAL CHANNEL NOT 2*SINGLE

ON THREADRIPPR ONLY USE QUAD CHANNEL NOT 2*DUAL


inside ram,(hardware ,IC and pcb )single,dual,quad not same ,completly diffrante ,, many people think = dual =2*single channel ram or quad =4* dual ram



you must use only ram, write on box QUAD for threadripper (dual for ryzen)

if you put wrong ram your system cant start , even if start , hiccops rip in windows, harm your cpu

in amd thteadripper ,change your ram to this
gskill ri4*8 3200=250$
or
gskil ripjaws4 4*4 2400=150$

www.amazon.com/G-Skill-Ripjaws-2400MHz-PC4-19200-Channel/dp/B00N1OZDPO

for ryzen use only ram write on box DUAL CHANNEL
gskill RGB trident z 3200 2*8 =180$
geil evo x 3200 2*8 =120$


not , only use 2400 or 3200 (best frequency stable) not 3000mhz

ATTENTION

Edited by raminro - 01 Oct 2017 at 10:57am
Back to Top
TANWare View Drop Down
Newbie
Newbie


Joined: 24 Sep 2017
Status: Offline
Points: 120 		Post Options Post Options   Thanks (0) Thanks(0)   Quote TANWare Quote  Post ReplyReply Direct Link To This Post Posted: 30 Sep 2017 at 8:43pm

I have sometimes noticed it can take some time for it to post from being powered on the first time. Be sure you have ram and video connected then after the power button wait 60 seconds or so.
Back to Top
MisterJ View Drop Down
Senior Member
Senior Member


Joined: 19 Apr 2017
Status: Offline
Points: 1097 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MisterJ Quote  Post ReplyReply Direct Link To This Post Posted: 30 Sep 2017 at 8:52am
sdlashley, forgot you are running Linux.  Google finds a number of free HW Monitors but I know so little about Linux, I can't really help.  Enjoy, John.
Fat1 X399 Pro Gaming, TR 1950X, RAID0 3xSamsung SSD 960 EVO, G.SKILL FlareX F4-3200C14Q-32GFX, Win 10 x64 Pro, Enermx Platimax 850, Enermx Liqtech TR4 CPU Cooler, Radeon RX580, BIOS 2.00, 2xHDDs WD
Back to Top
sdlashley View Drop Down
Newbie
Newbie


Joined: 28 Sep 2017
Location: Portland OR
Status: Offline
Points: 19 		Post Options Post Options   Thanks (0) Thanks(0)   Quote sdlashley Quote  Post ReplyReply Direct Link To This Post Posted: 30 Sep 2017 at 8:35am
Best I can tell, AIDA64 only runs on Windows.
HWMonitor... downloaded (along with mono and WinForms) and I just get a bunch of errors.
The one from Snap aka Ubuntu shows no sensors.
I have Pensor and GKrellM but they are pretty weak.
Might need some plugins or something to extend them. They may not exist yet cause Ryzen 1950x is so new.
Any suggestions?
Back to Top
MisterJ View Drop Down
Senior Member
Senior Member


Joined: 19 Apr 2017
Status: Offline
Points: 1097 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MisterJ Quote  Post ReplyReply Direct Link To This Post Posted: 29 Sep 2017 at 9:47am
sdlashley, I would update to 1.50.  I have been running it for a while with no problems.  If a 1.60 or higher shows up (again), please check here first.  Please use the Instant Flash in the BIOS.  This may be a little overkill, but follow this sequence:
1. Boot into BIOS, F9 (Load UEFI Defaults), save and exit.
2. Boot into BIOS, update BIOS using Instant Flash - will reboot.
3. Boot into BIOS, F9, save and exit.
You probably should wait until you install your new Power Supply and have a little run time to show stability.
Enjoy, John.
Fat1 X399 Pro Gaming, TR 1950X, RAID0 3xSamsung SSD 960 EVO, G.SKILL FlareX F4-3200C14Q-32GFX, Win 10 x64 Pro, Enermx Platimax 850, Enermx Liqtech TR4 CPU Cooler, Radeon RX580, BIOS 2.00, 2xHDDs WD
Back to Top
sdlashley View Drop Down
Newbie
Newbie


Joined: 28 Sep 2017
Location: Portland OR
Status: Offline
Points: 19 		Post Options Post Options   Thanks (0) Thanks(0)   Quote sdlashley Quote  Post ReplyReply Direct Link To This Post Posted: 29 Sep 2017 at 5:35am
can i indulge just a bit more... should I update to the latest bios or just let things go?
I freely admit I'm not much better than a novice.
I won't overclock. 
My graphics card is el cheapo.
I'm a database guy and plan to spin those hamsters doing database work.
Again, I can't thank you all enough.
Back to Top
MisterJ View Drop Down
Senior Member
Senior Member


Joined: 19 Apr 2017
Status: Offline
Points: 1097 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MisterJ Quote  Post ReplyReply Direct Link To This Post Posted: 29 Sep 2017 at 5:21am
sdlashley, you are very welcome.  Glad it's sorted!
Quote Another lesson learned... don't trust pcpartpicker.com!
This is the second time I have seen this!
Enjoy, John.
Fat1 X399 Pro Gaming, TR 1950X, RAID0 3xSamsung SSD 960 EVO, G.SKILL FlareX F4-3200C14Q-32GFX, Win 10 x64 Pro, Enermx Platimax 850, Enermx Liqtech TR4 CPU Cooler, Radeon RX580, BIOS 2.00, 2xHDDs WD
Back to Top
sdlashley View Drop Down
Newbie
Newbie


Joined: 28 Sep 2017
Location: Portland OR
Status: Offline
Points: 19 		Post Options Post Options   Thanks (0) Thanks(0)   Quote sdlashley Quote  Post ReplyReply Direct Link To This Post Posted: 29 Sep 2017 at 5:10am
EVGA G3 750 with 2 8 pin (4x4) cpu ordered from amazon and on its way.
I want to thank everyone who help me!
Another lesson learned... don't trust pcpartpicker.com!
If you don't hear back in a few days, assume it all worked wonderfully.
Back to Top
datonyb View Drop Down
Senior Member
Senior Member


Joined: 11 Apr 2017
Location: London U.K.
Status: Offline
Points: 3154 		Post Options Post Options   Thanks (0) Thanks(0)   Quote datonyb Quote  Post ReplyReply Direct Link To This Post Posted: 29 Sep 2017 at 4:59am
sdlashley

did you see my reply page 2 ?

im logging off now

to summerise

you are trying to plug the incorrect leads into the board

24 pin is correct

but you need to use eps/cpu 4+4 in location 9 (and NOT the pcie graphics) this is causing a short and locking up the board

and as said better idea to change the psu for one with two sets of eps/cpu 4+4

the evga g3 in 750w comes with two 4+4 leads


for the time being i suggest using the location 9 4+4 instead of the location2 4 pin
[url=https://valid.x86.fr/jpg250][/url]

3800X, powercolor reddevil vega64, gskill tridentz3866, taichix370, evga750watt gold
Back to Top
 Post Reply Post Reply Page  <12345 6>
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 0.132 seconds.