ASRock.com Homepage
Forum Home Forum Home > Technical Support > Intel Motherboards
  New Posts New Posts RSS Feed - H97 Killer Dual Channel Problem
  FAQ FAQ  Forum Search Search  Events   Register Register  Login Login

H97 Killer Dual Channel Problem
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Gera View Drop Down
Newbie
Newbie


Joined: 15 Sep 2015
Status: Offline
Points: 6 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Gera Quote  Post ReplyReply Direct Link To This Post Topic: H97 Killer Dual Channel Problem
    Posted: 15 Sep 2015 at 7:53pm
Hi All

Just registered to ask for help. If i put my RAM in dual channel in any slots it won´t boot and a red light bios stays on. Only boot if i put in single channel. This RAM shows as compatible in the mobo page but 16x and i have 2 sticks of 4gb  ( KHX24C11T3K2/16X )

Already set RAM speed in bios lower (1333) before changing the slots and nothing.

Here is my setup:

4790k
H97 Killer (Last z97 mobo died)
Kingston DDR3 2400 Beast 2x4
Seasonic 620w
BIOS: P2.40 (Latest)

In this review the test was with the same RAM and it runs in dual channel?? http://www.pcgameware.co.uk/reviews/motherboards/asrock-fatal1ty-h97-killer-motherboard-review/

One thing i noticed that he was running an old Beta BIOS (0.29B) maybe i have to downgrade BIOS? My CPU (4790K) will boot?
Back to Top
Xaltar View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 16 May 2015
Location: Europe
Status: Online
Points: 25028 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Xaltar Quote  Post ReplyReply Direct Link To This Post Posted: 15 Sep 2015 at 9:44pm
Have you tried clearing CMOS with the RAM modules installed in dual channel configuration?

Even if you have you can try doing a complete clear as described here.

More often than not these kinds of problem are UEFI related, this is why I recommend clearing CMOS every time you change RAM configuration or make any major hardware changes. Also check to be sure your RAM is seated properly in the slots, sometimes it will "clip" into place but not actually be properly in the slot all the way. Also check for any debris in the slots themselves.

Hopefully one of these suggestions resolves your problems. Welcome to the forums.
Back to Top
Gera View Drop Down
Newbie
Newbie


Joined: 15 Sep 2015
Status: Offline
Points: 6 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Gera Quote  Post ReplyReply Direct Link To This Post Posted: 16 Sep 2015 at 7:46am
Thanks for the reply but it didn´t work...
Back to Top
parsec View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 04 May 2015
Location: USA
Status: Offline
Points: 4996 		Post Options Post Options   Thanks (0) Thanks(0)   Quote parsec Quote  Post ReplyReply Direct Link To This Post Posted: 16 Sep 2015 at 3:18pm
The red UEFI/BIOS LED is on because the board did not POST with the memory for some reason.

You should be using the two black slots for the memory when using one DIMM per channel.

Did you use that memory in your other board that seems to have died?

Did you try each DIMM one at a time to be sure that both work?

You must clear the CMOS/BIOS after changing the slots the memory is used in, with no power to the board when that is done, of course.
Back to Top
Gera View Drop Down
Newbie
Newbie


Joined: 15 Sep 2015
Status: Offline
Points: 6 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Gera Quote  Post ReplyReply Direct Link To This Post Posted: 17 Sep 2015 at 5:52am
Hi, thanks for reply

Wii respond using your questions:

should be using the two black slots for the memory when using one DIMM per channel. YES USING BLACK OR RED SLOTS SAME PROBLEM

Did you use that memory in your other board that seems to have died? YES 

Did you try each DIMM one at a time to be sure that both work? YES ANY RAM IN ANY OF THE 4 SLOTS WORKS FINE

You must clear the CMOS/BIOS after changing the slots the memory is used in, with no power to the board when that is done, of course. YES DID THAT BEFORE TESTING. ALSO MEMTEST86 OK FOR HOURS.


Edited by Gera - 17 Sep 2015 at 5:57am
Back to Top
Gera View Drop Down
Newbie
Newbie


Joined: 15 Sep 2015
Status: Offline
Points: 6 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Gera Quote  Post ReplyReply Direct Link To This Post Posted: 22 Sep 2015 at 5:25am
After days of tests the shop said that the board was bad. It will be replaced to Gigabyte H97 D3H. Hope i get lucky this time
Back to Top
Nemkell View Drop Down
Newbie
Newbie
Avatar

Joined: 19 Oct 2015
Location: Hungary
Status: Offline
Points: 6 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Nemkell Quote  Post ReplyReply Direct Link To This Post Posted: 19 Oct 2015 at 6:50pm
Originally posted by Gera Gera wrote:

After days of tests the shop said that the board was bad. It will be replaced to Gigabyte H97 D3H. Hope i get lucky this time


 
Did that change solve your problem?
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 0.734 seconds.