was working - now not

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   Good spot Parsec, it could be that his RAM's XMP profile is trying to set the BCLK to 125 and causing all this. I wish XMP didn't do this with faster RAM, it seems to cause a lot of issues.

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Xaltar Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 23738	Post Options Post Reply Quote Xaltar Report Post Thanks(0) Quote Reply Topic: was working - now not Posted: 24 Oct 2015 at 1:58pm
	Good spot Parsec, it could be that his RAM's XMP profile is trying to set the BCLK to 125 and causing all this. I wish XMP didn't do this with faster RAM, it seems to cause a lot of issues.

parsec Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Joined: 04 May 2015 Location: USA Status: Offline Points: 4996	Post Options Post Reply Quote parsec Report Post Thanks(0) Quote Reply Posted: 24 Oct 2015 at 1:31pm
	A Dr Debug/POST code of 00 normally means a problem with the CPU. I would not expect that by simply using an XMP profile. That is, unless the XMP profile is so extreme that the CPU cannot even function. Does the BIOS have a XMP profile option? It does in the DRAM configuration section of the OC Tweaker screen. Code 99 means a problem with a PCIe device. You said you don't have anything in the PCIe slots, right? For now, I would suggest not using the XMP switch, set it to Off. What model of memory are you using, and what speed is it? Which memory slots are you using if you are using one or two DIMMs?


Xaltar Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Joined: 16 May 2015 Location: Europe Status: Offline Points: 23738	Post Options Post Reply Quote Xaltar Report Post Thanks(0) Quote Reply Posted: 24 Oct 2015 at 1:04pm
	Yes that is the correct way, or at least it should work. You can try using this method to ensure all values are reset. Also check if there is a BIOS update for your board, the Z100 platform is still in it's infancy and as such, there are still teething problems which are being worked out.

asrrg Members Profile Send Private Message Find Members Posts Add to Buddy List Newbie Joined: 24 Oct 2015 Status: Offline Points: 3	Post Options Post Reply Quote asrrg Report Post Thanks(0) Quote Reply Posted: 24 Oct 2015 at 10:17am
	New build and I had verified computer ran correctly with default settings (both with on-board video and after video card was installed) Z170 OC FORMULA/A/ASRK Intel 6700K RAM being used is listed in memory support list Now - ready to start overclocking 1. Turned off computer, pulled out power cord, waited 15+ seconds 2. Action: Flipped "XMP Switch" from off to on 3. Turned on computer: debug code 00 Played with it a bit, tried things like bios reset, etc... 4. repeat step 1 5. Action: Flipped "XMP Switch" from on to off 6. Turned on computer: debug code 00 (immediately - no fan) Played with it a bit, tried things like bios reset, etc... 7. repeat step 1 8. Action: Flipped "BIOS Selection" from 'A' to 'B' 9. Turned on computer: (runs for a bit) debug code 99 10. repeat step 1 11. Action: physically remove video card (all PCI slots are now unused) 12. Turned on computer: (runs for a bit) debug code 99 I am now lost at what to try next. Please advise! Also, am I using the 'Clear CMOS Switch' correctly? turn off computer, unplug computer wait 15+ seconds hold 'Clear CMOS Switch' 5+ seconds plug computer in turn on computer