|
Ryzen 3000 series support |
Post Reply 
|
Page <1 34567 108> |
| Author | ||
DaReaLDeviL 
Newbie 
Joined: 20 Jul 2020 Status: Offline Points: 5 |
 Post Options
 Thanks(0)
 Quote Reply
 Posted: 20 Jul 2020 at 4:11am |
|
|
I just bought a 3600XT and a B550 Phantom Gaming-ITX/ax - how can I undervolt my cpu so that it dont get that hot? Didn't find any offset or something simular. Maybe I'm blind?
Thank in advanced! |
||
 |
||
|
Silent84
Newbie
Joined: 21 Jun 2020 Location: Romania Status: Offline Points: 3 |
Post Options
Thanks(0)
Quote Reply
Posted: 19 Jul 2020 at 6:51pm |
|
Yeah mate the bios is very slow on asrock, this is the last time i will buy a motherboard from them! |
||
|
||
|
marcin2468
Newbie
Joined: 17 Sep 2019 Status: Offline Points: 54 |
Post Options
Thanks(0)
Quote Reply
Posted: 17 Jul 2020 at 11:07pm |
|
Asrock so slow update bios for x470 taichi ultimate. Every b450 asrock board have already new agesa. I'm disappointed in this. I will look also for new motherboard. |
||
|
||
|
cx5
Senior Member 
Joined: 15 Sep 2017 Location: Hong Kong Status: Offline Points: 2383 |
Post Options
Thanks(0)
Quote Reply
Posted: 15 Jul 2020 at 1:38pm |
|
|
hello there,
The more ram sticks used, the less speed to run, beyond below speed is overclock and depend on luck. 
|
||
|
x370taichi@3.50gen4
AX750 Optane900P SN770 3800x PosdonZro4 BarrowPWM-17w>420x140x28 XFX SWFT319 6900XT MSI RX560 LP to get Fluid Motion BlueskyFRC 75hz |
||
|
||
|
BowlofPixels
Newbie
Joined: 08 Jul 2020 Status: Offline Points: 1 |
Post Options
Thanks(0)
Quote Reply
Posted: 08 Jul 2020 at 11:40pm |
|
|
Hey guys. New to the forum. I have an Taichi x399 with a 1920x Threadripper and F4-320016D-16GV x8 setup and I'm unable to get the BIOS to:
1) see C1 and C2 slotted memory regardless of which modules I swap in 2) get the board to OC the memory to it's full 3200Mhz potential I believe I am on the latest firmware as this is an RMA board (long story of a CPU failure where I couldn't determine whether the board or CPU was the culprit). Any help would be greatly appreciated. This is also my first post so hopefully this is in the right thread. |
||
|
||
|
ViCe
Newbie
Joined: 08 Oct 2019 Location: Russia Status: Offline Points: 34 |
Post Options
Thanks(0)
Quote Reply
Posted: 06 Jul 2020 at 1:39pm |
|
|
I finally got a refund for x470 Taichi and found out what problem was: seller's warranty department provided me with very interesting information - near 30% of mobo is defective from factory as my one (CMOS, BIOS flash etc.), bios department in ASRock tests bios on consumers, collect information from forums and then try to fix problems, but without inside tests. In June there are near 40 RMA and refunds and all of them are because of problems with bios, so, it can be an indicator of quality of ASRock mobos. I bought Asus crosshair vii and there is no problem. So, my advice - forget about ASRock, it's very bad manufacturer
|
||
|
||
|
3600er
Newbie
Joined: 30 Jun 2020 Status: Offline Points: 2 |
Post Options
Thanks(0)
Quote Reply
Posted: 30 Jun 2020 at 5:27am |
|
|
@MurkyWanders in the bios of my b450mpro4 board (bios 3.90) is a setting called Max Voltage Offset (AMD Overclocking, NBIO, SMU) i guess. This setting has the values AUTO, 25, 50, 75 and 100. You can try to apply an negative vcore Offset together with 100 for example. This will block the vcore. 100 is the strongest. The CPU stays cooler, too. But the boost is not going to the max anymore. I`m using an offset of -0.05V and Max Voltage Offset is 25. PBO at auto.
|
||
|
||
|
MurkyWanders
Newbie
Joined: 28 Jun 2020 Status: Offline Points: 1 |
Post Options
Thanks(0)
Quote Reply
Posted: 28 Jun 2020 at 2:56pm |
|
|
Hey all, I'm having issues with my X570 Taichi and a 3900x. During normal use my Vcore is 1.49v, and I feel that is just too high. I tried the Mv offset and it didn't seem to do anything. I've messed around quite a bit the last few days and outside of an all core overclock I think It's beaten me. I would prefer to let it boost on its own for better single core clocks for gaming, but can't get the voltage down without a bit of a cascade off fires to put out. Thanks in advance for any help. I'd kiss whoever can.
|
||
|
||
|
Silent84
Newbie
Joined: 21 Jun 2020 Location: Romania Status: Offline Points: 3 |
Post Options
Thanks(0)
Quote Reply
Posted: 28 Jun 2020 at 1:11pm |
|
|
@user_mac01 thank you buddy, i appreciated but i work in this domain for 15 years, and i never saw sensor, to disappear like this in a new mobo, i test msi tomahawk intel and amd version, gigabyte b450, elite, pro etc, my old pc use an old 17 3770 with asrock b75 pro 3 for 8 years, and never had issues, i am sure 90% is the mobo doing this!
|
||
|
||
|
user_mac01
Newbie
Joined: 28 Jun 2020 Location: Australia Status: Offline Points: 2 |
Post Options
Thanks(0)
Quote Reply
Posted: 28 Jun 2020 at 12:16pm |
|
|
JayzTwoCents has a YT vid upload HowTo (installing MS Win 10), URL = https://www.youtube.com/watch?v=RYYoCXh2gtw&t=2s
He explains this very thing: detecting and setting your NVMe SSD drive and all the rest when installing a new PC build OS. Including what to set in BIOS, k/b shortcut config interventions and how to detect the drive to format it, employing UEFI usb stick OS install... In short everything you need to know from build complete to firing up a Star killer primary weapons system. |
||
|
I don't know everything, but its what I do know that bothers people.
|
||
|
||
|
Post Reply
|
Page <1 34567 108> |
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
marcin2468 wrote: